Issue with Strong SRT 5011 TNT Decoder Solved

Question

Hello,

I bought a TNT decoder from the brand Strong, model SRT 5011. When I start the initialization, I get the following message "Antenna power overload - Turn off the decoder - Check the antenna." The solution to this message is not in the user manual.

Does anyone have the solution or any ideas on the matter?

Thank you for your promptness.

Antoine M

tigen · Accepted Answer

For your antenna overload issue, simply go into the menu, then installation, next system configuration, and finally antenna power, and there you need to select off.

Nesta · Answer

Hi, it happened to me before. It's the power supply for an indoor antenna that is activated. So at startup, you need to choose either before installation or after in the setup; antenna power supply should be set to off since the TNT is probably connected to an outdoor antenna. That's it, bye.

strongfranceservice · Answer

Hello,  This is Strong France,  The support service has just opened.  You can reach us for any technical issues:  0826 029 928 indigo number  strongfranceservice@strongsat.com  Have a nice day!

nanar · Answer

Hello,

I bought this TNT decoder today and I have exactly the same problem as you.
I read your proposed solutions. Yes, but now, every time I plug in the decoder, it directly displays this message "antenna power overload" and I can't access any menu...
Any idea??

Thanks in advance! I'd like to watch the rugby match tomorrow night, heheheheheh.

mguebel · Answer

I had the same problem. The cause has been described above, but if we can't do anything other than turn it off and on again, only to end up with the same message every time ... not great :-(
I managed to solve it by turning the decoder back on after --unplugging-- the antenna :-)
Then go to the menu to cancel the antenna power option. And then plug everything back in :-)

nanar · Answer

Phew!! It's working now!! Just before the match between France and Argentina.... In hindsight, I think if it hadn't worked for the match, it wouldn't have been a tragedy, hehehe!!

rulio · Answer

Hello
I'm having trouble with my receiver, all the channels are mixed up, for example: TF1 = 372, etc. When I do a new channel search, they reinstall in the same order? Can you help me?
PS/The receiver works with an indoor antenna.

pluto48 · Answer

Hello,
I have a Strong 6420 digital satellite decoder for TNT, and I would like to know how to change the selection of regional programs on France 3 because I selected the wrong region during installation. I can't find the procedure. Thank you.

pluto48 · Answer

Hello, thank you SAMLED and nialasamled for your help regarding the technical issue with the regional channel on the satellite TNT. I will try it right away.

gonzmarie · Answer

Hello,
I bought a strong 5120 decoder and during my move, I lost the user manual. Could someone kindly either point me to a link where I could download it or, if someone has scanned it, could you please send it to me? Thank you in advance to everyone.

cris83 · Answer

Good evening  I have the same problem, I also lost the manual. Can someone tell me where I can get it? Thank you very much.

Gérard · Answer

Hello,
I intend to buy one of these decoders. Can we also receive channels like TF1, France 2, M6, etc. outside of TNT?
Thank you, friends, for your response.
Can you give me some advice on the quality of one of these products?
Gérard

Gérard · Answer

Thank you Grandma for the information.

auni · Answer

Hello  I have a Strong 5011 decoder that was working very well.  For the past two days, I no longer have TF1, Channel 10, and Channel 12.  Does anyone have a solution?

amelie · Answer

Hello everyone, I bought a Strong decoder for TNT yesterday, but it freezes. Everything goes well until it tells me to download the new version 1.5, I think. It downloads but freezes after reaching 100%, and I no longer have access to anything, including the menu. Can someone help me?

luc01 · Answer

I installed a Strong 5011 TNT decoder on a television a few months ago and everything was fine. This morning, I acquired a TV with built-in TNT, so I installed the decoder on another television... automatic channel installation and there, I'm missing lots of channels like TF1, France 2, France 3, etc. Can anyone give me information?

GAROU · Answer

HELLO, CAN WE RECEIVE TNT BY PLUGGING IN A CABLE ANTENNA?

syl · Answer

Good evening,
having installed this digital terrestrial decoder today which gives me a very nice image with just an indoor antenna, I have a problem regarding the use of the remote control. Is it normal to have to use the television remote to turn it on?
Thank you in advance for your replies.

seo · Answer

Hello I just updated the software of the strong 6410 and afterwards it went into error 08 and now I can't turn it off when unplugging it and I no longer have access to the menu and when I plug it back in, it updates every time and goes back into error. Thank you for your help.

kilam · Answer

Hello, I bought a TNT and I wanted to connect it with my satellite dish which I receive with Arab countries and also Multivision, but nothing shows up because I have the decoder for Arab countries and I bought a T to connect the input from the satellite dish. I created a (T) that goes to my decoder and the other to my TNT, but the scan doesn't pick anything up and it always says no signal. If anyone can help me, thanks.

dinobib · Answer

Hello, Like others before me, I had a problem with the strong 6410 model to access the TNTSAT package. I hadn't finished the configuration and searching for channels when it suggested I download new firmware. Foolishly, I confirmed it, but at the end of the download (D001 to D100), it didn't restart as indicated in the manual and showed nothing on the front panel. After an hour of waiting, still nothing, so I decided to turn it off with the back button and restart it, but it seems that the download procedure automatically resumes and always ends with a PB003 message. This behavior happens every time I turn the decoder back on, and it's impossible to access the menu, which supposedly has a factory reset section. If anyone who has had the same problem has found a solution, it would be nice to share it. Thank you in advance.

testltout · Answer

Normally, you need to restart as many times as necessary until the update is complete. After the D00 --------> D100, there are F00 -------------> F100, and yes On some devices, you have to restart much more than 10 times. Welcome to the land of the strong's traps.

dinobib · Answer

Thank you Testitout. That's exactly it. After 12 attempts, the update was successful. Now I have a week left to return it, so even if it works, I'm almost tempted to return it to exchange it for a Samsung model. Thank you for the help.

boubou · Answer

I have the same problem, my remote control is not responding anymore, I don't know what to do.

boubou · Answer

can someone answer me

dinobib · Answer

repeat the operation (turn off, turn on, redownload) until the fs increment to 100 as Testitout said. It takes a lot of time with a reboot each time but there's no other way. On the tvnt forum, there is a page about this problem starting from page 8 or so: http://www.tvnt.net/forum/strong-srt-6410-6420-canal-ready-tntsat-t11660-1260.html good luck and especially patience.

lecanadien · Answer

Good evening! With the Strong, I notice that there are only all sorts of problems.  As for me, I have installed 2 Sagem satellite TNT decoders, the installation was perfect and there are no issues.  It's up to you, Strong made in China is not very renowned for its reliability.  Best regards  LECANADIEN

EWAJ · Answer

FROM Eric Disable the external power supply of the antenna, there is probably a function that allows it (see the documentation). Good evening

ksey · Answer

Hi  the demo crashed during its software update (regardless of the version)  the only solution is to replace the device or repair it (if it's under warranty)  I bought the 6420 today and it crashed (that's the biggest flaw of this device).  I went back to Darty and they replaced it for me.

Christian · Answer

I have a very good signal at 91%, everything went very smoothly during the initial setup (today), but while downloading the software the decoder seems to be stuck (for over an hour). You mentioned a reset; how can we regain access to the settings and start over since I can't access the menu?  Thank you in advance and have a great weekend.

mayelyne · Answer

Hello, since Friday evening I no longer have any TNT channels for no reason. I've tried to restart it but nothing works. Could someone help me? Thank you.

jecherche · Answer

I can't seem to save my personal ranking of non-DTT channels. After three attempts, I'm getting a bit tired of it because it's a nice piece of work.

jecherche · Answer

Following message 39, I would like to clarify that I own a STRONG SRT 6420.

kikette · Answer

Hello, I have a Strong 6410 decoder that I installed in December. I changed the decoder once and it worked perfectly since then; I have always refused updates. Unfortunately, a friend came over and accidentally started an update, and since yesterday, I only have TF1 and M6, with a message saying the signal is too weak on all the others. What should I do?

stef77 · Answer

Good evening. So, my brother gave me his TNT decoder SRT 5120 today. It worked perfectly at his place. I plug it in at mine and to my surprise, there’s no signal and therefore it can't find any channels, of course. Yet, I have connected the terrestrial antenna to the IN input properly. I don’t understand; I think I’ve tried everything. I even reset it to factory settings, but nothing works. My antenna cable works perfectly since when I connect it directly to the TV socket, I have excellent reception. So, if someone could help me, thanks in advance.

mimi38 · Answer

I have an LG HD READY TCD television and an HD TNTSAT decoder from SAGEM sold for TNTSAT. I want to be able to view HD TV, and for that, I purchased an HDMI-DVI cable to connect the TNT decoder and the LCD TV to the appropriate outputs. However, with the cable connected, I have nothing on the TV. According to the LG TV manual, I have programmed the screen for HD, but I see nothing on the screen. If anyone has any ideas on how to make this TV, which was also purchased for HD, and the SAGEM HD decoder work, I would be grateful!

julienpiel · Answer

Hello,
I can't manage to set the channels, etc...
My problem is that it keeps showing me a technical message saying that I need to reset the decoder, and when I do, I always get the same message, so I don't understand.
Could you please help me?
Thanks in advance
julienpiel

tsf85 · Answer

Hello I have a problem with the strong 6420 for the past 2 days, I can't put it in sleep mode. I did a quick check, the power button is fine. Has anyone else had the same problem? The flip side is that at the first power outage, I might not be able to turn it back on.  (It still looks like a real piece of junk based on the posts in the forum).

Drakkard · Answer

Hello

I have a STRONG 5011 TNT decoder. I'm having an issue when I watch the series CSI. I receive it in the original version with subtitles. I have to switch back to the TV to watch it in French. Is there a setting that would allow me to watch it in French via TNT? Is it a software issue? Can someone help me?

heigi · Answer

Hello, I have a Strong decoder, TNT, and I can't turn off the subtitles. Thank you for your help.

calimero53 · Answer

In the settings, you can enable or disable the internal antenna amplifier on the decoder; if it is enabled, try disabling it.

kiki · Answer

In the settings of the adapter for antenna power, set to no.

lulu · Answer

Je possède un décodeur Strong, mais j'ai un problème : je n'ai plus du tout de chaînes depuis quelques jours et je n'ai pas de qualité de signal. Que dois-je faire ?

Issue with Strong SRT 5011 TNT Decoder

43 réponses

Texture issues in enshrouded

Driver his

Peritel to hdmi conversion

How to access the bios on a compaq notebook

Dsi won't turn on anymore

Search for a song with the lyrics

Left mouse click, touchpad click inactive

Codes stronghold crusader

Stuck computer system repair

Disable write protection mp3 player