[Mandriva 2007] Erreur compil drv sagem fast

Résolu
neolux -  
salut @ tous,

Voila , j'ai installé la mandriva 2007 Power pack sur mon ordi, et en voulant configurer ma connection internet avec un modem sagem fast800 E3 en suivant les procedures :

$ ./configure
$ make uninstall
$ make clean
$ make

j'ai eu un message d'erreur avec la commande make :

WARNING: Symbol version dump /usr/src/linux-2.6.17-5mdv/Module.symvers
is missing; modules will have no dependencies and modversions.

(j'ai decompresser avant les drivers "eagle-usb-2.3.3.tar.bz2" et installer GCC et Kernel-Source @ partir du centre de config de mandriva)

Donc je n'ai pas pu compiler les drivers.

Avans d'éssayer de compiler les drivers, j'ai configurer une connection graphiquement (en mode graphique) avec les drivers eagle-atm sans aucun résultat.

SVP si quelqu'un pourrait m'aider pas @ pas , je suis nouveau sous linux et vraiment nul.

merci d'avance!

9 réponses

  1.  tufs Contributeur
    salut

    Mandriva 2007 Power pack est une version recente le Kernel aussi ... tapes dans une console => 

    :~$ uname -r


    puis voir là ( extrait du lien ) ;
    Depuis le 2.6.15, le pilote est inclu dans le noyau de kernel.org et plus aucune installation n'est necessaire

    GPL Driver => Eagle Chipset ==>> http://www.eagle-usb.org/
    0
    1. neolux Auteur
      salut, et merci tufs de m'avoir repondu

      je vais voir le lien!
      0
      1. neolux Auteur
        salut c'est encore moi.

        aparement je suis plus nulll que je le pensais, j'ai rien compris ou presque rien .... aprés une semaine sous linux je pence que c'est normale ........... non??

        récapitulons, eagle-atm est inclus dans le noyeau @ partir de la version 2.6.15, donc pas besoin d'installation.

        mais pour la configuration c'est la galére...enfin pour moi en tout cas!

        pas de eagleconfig ni eaglecrt

        j'ai lu la documentation que tufs ma prescrite : http://atm.eagle-usb.org/wakka.php?wiki=UeagleAtmDocFr

        et qui semble la bonne, mais encore une fois , j'ai rien pigé !

        je suis passer directement @ la section "Paramétrage de la connexion internet" pour "PPPoE".

        pour # modprobe br2684 c bon , mais quant je met :

        # br2684ctl -c 0 -e x vpi.vci la console m'affiche un message du genre commande incorrecte.

        donc qu'elle est la procedure (decrite simplement) pour configurer mon modem en PPPoE LLC 0/35 , et si il ya des fichiers @ modifier.

        Merci de votre aide.
        0
        1. tufs Contributeur
          re

          Il faut peut-etre que tu charges le module à la main <<< OK

          tape cette commande : ( chez moi ) =>

          tufs@debian:~$ uname -r
          2.6.18-2-686
          ( chez moi le module est inclus )

          tufs@debian:~$ /sbin/modinfo ueagle-atm
          filename: /lib/modules/2.6.18-2-686/kernel/drivers/usb/atm/ueagle-atm.ko
          author: Damien Bergamini/Matthieu Castet/Stanislaw W. Gruszka
          description: ADI 930/Eagle USB ADSL Modem driver
          license: Dual BSD/GPL
          vermagic: 2.6.18-2-686 SMP mod_unload 686 REGPARM gcc-4.1
          depends: usbcore,usbatm,firmware_class

          apres tu passes en root ( su - ) et tu charges le module

          # modprobe ueagle-atm

          puis tu tapes ça pour voir si le module est present ...

          tufs@debian:~$ lsmod
          Module Size Used by
          isofs 32540 1
          udf 73156 0
          nvidia 4549908 12

          ps : moi j ai pas charger le module ....

          Voilà si ça peut-aider .....

          0
          1. neolux Auteur
            Salutation,

            Là j’avoue, c’est trop dure pour moi.

            Effectivement tu avais raison tufs, les drivers sont incluent dans le noyau, et mon modem ce synchronise ……. mais toujours pas de connexion !

            Après avoir fait de longues recherches sur le net pour trouver un cas similaire, je suis tombé sur cette adresse :
            http://remi.collet.free.fr/index.php?2006/02/24/113-configuration-du-pilote-ueagle-atm

            J’ai procéder comme suit :

            1-installer ueagle-data-1.1.tar.gz
            $ su –
            # cd /lib/firmware
            # tar xvzf /chemin/download/ueagle-data-1.1.tar.gz
            # mv ueagle-data-1.1 ueagle-atm

            (malgré que les drivers sont dans le noyau, mais bon on sais jamais)

            2- Consulter le journal système : tail -f /var/log/messages | grep ueagle-atm

            l@ rien du tout ! alors j’ai enlever le ‘| grep ueagle-atm ‘

            [root@localhost Desktop]# tail ­f /var/log/messages
            Nov 30 20:17:43 localhost pppd[3781]: Couldn't get channel number: Input/output error
            Nov 30 20:17:47 localhost pppd[3781]: Couldn't get channel number: Input/output error
            Nov 30 20:17:47 localhost pppd[3781]: Exit.
            Nov 30 20:18:58 localhost drakconnect[3751]: modified file /etc/modprobe.conf
            Nov 30 20:18:58 localhost drakconnect[3751]: running: dmidecode
            Nov 30 20:18:58 localhost drakconnect[3751]: to put in /etc/modules
            Nov 30 20:18:58 localhost drakconnect[3751]: modified file /etc/modules
            Nov 30 20:18:58 localhost drakconnect[3751]: to put in /etc/modprobe.preload via­agp
            Nov 30 20:18:58 localhost drakconnect[3751]: modified file /etc/modprobe.preload

            Nov 30 20:18:58 localhost drakconnect[3751]: ### Program is exiting ###

            et dans la section Enregistrer les identifiants, je sais même pas comment créer un fichier !

            au démarrage de linux il y a un message qui s’affiche : Device Not Accepting Adress 2 : Error 110 je pence !

            Alors tufs si tu @ quelques idées, elles ne serons pas de trop.

            encore merci.
            0
        3. tufs Contributeur
          salut

          Que donne ses commandes : 

          ~$ /sbin/modprobe -l -t usb | grep usb


          ~$ ps -ef|grep eagle


          donne aussi le resultat des commandes si-dessus mercie ...
          tufs@debian:~$ lsmod

          donne en detail la procedure que tu as suivie avec les resultat des commandes ( important ) http://remi.collet.free.fr/

          bonne chance !
          0
          1. neolux Auteur
            salut tufs et merci de me supporté ;-)

            **** premiérement pour la commande ''dmes'' (je ne sais pas si sa peut servir) :

            [root@localhost Desktop]# dmesg
            Linux version 2.6.17­5mdv (rtp@octopus.mandriva.com) (gcc version 4.1.1 20060724 (prerelease)
            (4.1.1­3mdk)) #1 SMP Wed Sep 13 14:32:31 EDT 2006
            BIOS­provided physical RAM map:
            BIOS­e820: 0000000000000000 ­ 000000000009fc00 (usable)
            BIOS­e820: 000000000009fc00 ­ 00000000000a0000 (reserved)
            BIOS­e820: 00000000000f0000 ­ 0000000000100000 (reserved)
            BIOS­e820: 0000000000100000 ­ 0000000017ff0000 (usable)
            BIOS­e820: 0000000017ff0000 ­ 0000000017ff3000 (ACPI NVS)
            BIOS­e820: 0000000017ff3000 ­ 0000000018000000 (ACPI data)
            BIOS­e820: 00000000ffff0000 ­ 0000000100000000 (reserved)
            0MB HIGHMEM available.
            383MB LOWMEM available.
            On node 0 totalpages: 98288
            DMA zone: 4096 pages, LIFO batch:0
            Normal zone: 94192 pages, LIFO batch:31
            DMI 2.2 present.
            ACPI: RSDP (v000 VIA692 ) @ 0x000f7270
            ACPI: RSDT (v001 VIA692 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x17ff3000
            ACPI: FADT (v001 VIA692 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x17ff3040
            ACPI: DSDT (v001 VIA692 AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
            ACPI: PM­Timer IO Port: 0x4008
            Allocating PCI resources starting at 20000000 (gap: 18000000:e7ff0000)
            Built 1 zonelists
            Kernel command line: root=/dev/hda5 resume=/dev/hda13 splash=verbose vga=791
            bootsplash: verbose mode.
            Local APIC disabled by BIOS ­­ you can enable it with "lapic"
            mapped APIC to ffffe000 (0130a000)
            Enabling fast FPU save and restore... done.
            Enabling unmasked SIMD FPU exception support... done.
            Initializing CPU#0
            PID hash table entries: 2048 (order: 11, 8192 bytes)
            Detected 798.121 MHz processor.
            Using pmtmr for high­res timesource
            Console: colour dummy device 80x25
            Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
            Inode­cache hash table entries: 32768 (order: 5, 131072 bytes)
            Memory: 384612k/393152k available (2426k kernel code, 7524k reserved, 756k data, 244k init, 0k
            highmem, 0k BadRAM)
            Checking if this processor honours the WP bit even in supervisor mode... Ok.
            Calibrating delay using timer specific routine.. 1598.22 BogoMIPS (lpj=3196446)
            Mount­cache hash table entries: 512
            CPU: After generic identify, caps: 0387f9ff 00000000 00000000 00000000 00000000 00000000
            00000000
            CPU: After vendor identify, caps: 0387f9ff 00000000 00000000 00000000 00000000 00000000
            00000000

            CPU: L1 I cache: 16K, L1 D cache: 16K
            CPU: L2 cache: 256K
            CPU serial number disabled.
            CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000
            Intel machine check architecture supported.
            Intel machine check reporting enabled on CPU#0.
            Checking 'hlt' instruction... OK.
            SMP alternatives: switching to UP code
            Freeing SMP alternatives: 16k freed
            checking if image is initramfs... it is
            Freeing initrd memory: 120k freed
            ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
            ACPI: setting ELCR to 0200 (from 0e00)
            CPU0: Intel Pentium III (Coppermine) stepping 06
            SMP motherboard not detected.
            Local APIC not detected. Using dummy APIC emulation.
            Brought up 1 CPUs
            migration_cost=0
            NET: Registered protocol family 16
            ACPI: bus type pci registered
            PCI: PCI BIOS revision 2.10 entry at 0xfb220, last bus=1
            Setting up standard PCI resources
            ACPI: Subsystem revision 20060127
            ACPI: Interpreter enabled
            ACPI: Using PIC for interrupt routing
            ACPI: PCI Root Bridge [PCI0] (0000:00)
            PCI: Probing PCI hardware (bus 00)
            ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
            Boot video device is 0000:01:00.0
            ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
            ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
            ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *9
            ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *9
            ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
            Linux Plug and Play Support v0.97 (c) Adam Belay
            pnp: PnP ACPI init
            pnp: PnP ACPI: found 13 devices
            PnPBIOS: Disabled
            PCI: Using ACPI for IRQ routing
            PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
            PCI: Bridge: 0000:00:01.0
            IO window: d000­dfff
            MEM window: d0000000­d7ffffff
            PREFETCH window: d8000000­dfffffff
            PCI: Setting latency timer of device 0000:00:01.0 to 64
            NET: Registered protocol family 2
            IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
            TCP established hash table entries: 16384 (order: 5, 131072 bytes)
            TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
            TCP: Hash tables configured (established 16384 bind 8192)

            TCP reno registered
            apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
            apm: overridden by ACPI.
            audit: initializing netlink socket (disabled)
            audit(1164926974.984:1): initialized
            Total HugeTLB memory allocated, 0
            VFS: Disk quotas dquot_6.5.1
            Dquot­cache hash table entries: 1024 (order 0, 4096 bytes)
            Initializing Cryptographic API
            io scheduler noop registered
            io scheduler anticipatory registered (default)
            io scheduler deadline registered
            io scheduler cfq registered
            Activating ISA DMA hang workarounds.
            vesafb: framebuffer at 0xd8000000, mapped to 0xd8880000, using 6144k, total 16384k
            vesafb: mode is 1024x768x16, linelength=2048, pages=9
            vesafb: protected mode interface info at c000:7cf3
            vesafb: scrolling: redraw
            vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
            Console: switching to colour frame buffer device 128x48
            fb0: VESA VGA frame buffer device
            isapnp: Scanning for PnP cards...
            isapnp: No Plug & Play device found
            Real Time Clock Driver v1.12ac
            Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
            serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
            serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
            00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
            00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
            RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
            Uniform Multi­Platform E­IDE driver Revision: 7.00alpha2
            ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
            VP_IDE: IDE controller at PCI slot 0000:00:07.1
            PCI: VIA IRQ fixup for 0000:00:07.1, from 255 to 0
            VP_IDE: chipset revision 16
            VP_IDE: not 100% native mode: will probe irqs later
            VP_IDE: VIA vt82c596b (rev 23) IDE UDMA66 controller on pci0000:00:07.1
            ide0: BM­DMA at 0xe000­0xe007, BIOS settings: hda:DMA, hdb:DMA
            ide1: BM­DMA at 0xe008­0xe00f, BIOS settings: hdc:DMA, hdd:DMA
            Probing IDE interface ide0...
            hda: SAMSUNG SP1203N, ATA DISK drive
            hdb: Maxtor 32049H3, ATA DISK drive
            ide0 at 0x1f0­0x1f7,0x3f6 on irq 14
            Probing IDE interface ide1...
            hdc: HL­DT­STDVD­ROM GDR8162B, ATAPI CD/DVD­ROM drive
            hdd: LITE­ON DVDRW SOHW­1693S, ATAPI CD/DVD­ROM drive
            ide1 at 0x170­0x177,0x376 on irq 15
            hda: max request size: 512KiB
            hda: 234493056 sectors (120060 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(66)
            hda: cache flushes supported

            hda: hda1 hda2 hda4 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 hda12 hda13 hda14 >
            hdb: max request size: 128KiB
            hdb: 40021632 sectors (20491 MB) w/512KiB Cache, CHS=39704/16/63, UDMA(66)
            hdb: cache flushes not supported
            hdb: hdb1
            PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
            serio: i8042 AUX port at 0x60,0x64 irq 12
            serio: i8042 KBD port at 0x60,0x64 irq 1
            mice: PS/2 mouse device common for all mice
            md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
            md: bitmap version 4.39
            TCP bic registered
            NET: Registered protocol family 1
            Using IPI No­Shortcut mode
            ACPI wakeup devices:
            PWRB PCI0 USB0 USB1 UAR1 UAR2 LPT1
            ACPI: (supports S0 S1 S4 S5)
            BIOS EDD facility v0.16 2004­Jun­25, 2 devices found
            Freeing unused kernel memory: 244k freed
            input: AT Translated Set 2 keyboard as /class/input/input0
            kjournald starting. Commit interval 5 seconds
            EXT3­fs: mounted filesystem with ordered data mode.
            input: ImPS/2 Generic Wheel Mouse as /class/input/input1
            hdb: dma_intr: status=0x51 { DriveReady SeekComplete Error }
            hdb: dma_intr: error=0x84 { DriveStatusError BadCRC }
            ide: failed opcode was: unknown
            hdb: dma_intr: status=0x51 { DriveReady SeekComplete Error }
            hdb: dma_intr: error=0x84 { DriveStatusError BadCRC }
            ide: failed opcode was: unknown
            hdb: dma_intr: status=0x51 { DriveReady SeekComplete Error }
            hdb: dma_intr: error=0x84 { DriveStatusError BadCRC }
            ide: failed opcode was: unknown
            hdb: dma_intr: status=0x51 { DriveReady SeekComplete Error }
            hdb: dma_intr: error=0x84 { DriveStatusError BadCRC }
            ide: failed opcode was: unknown
            hdb: dma_intr: status=0x51 { DriveReady SeekComplete Error }
            hdb: dma_intr: error=0x84 { DriveStatusError BadCRC }
            ide: failed opcode was: unknown
            hdb: dma_intr: status=0x51 { DriveReady SeekComplete Error }
            hdb: dma_intr: error=0x84 { DriveStatusError BadCRC }
            ide: failed opcode was: unknown
            ts: Compaq touchscreen protocol output
            usbcore: registered new driver usbfs
            usbcore: registered new driver hub
            USB Universal Host Controller Interface driver v3.0
            ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
            PCI: setting IRQ 10 as level­triggered
            ACPI: PCI Interrupt 0000:00:07.2[D] ­> Link [LNKD] ­> GSI 10 (level, low) ­> IRQ 10
            uhci_hcd 0000:00:07.2: UHCI Host Controller
            uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1

            uhci_hcd 0000:00:07.2: irq 10, io base 0x0000e400
            usb usb1: configuration #1 chosen from 1 choice
            hub 1­0:1.0: USB hub found
            hub 1­0:1.0: 2 ports detected
            ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
            ACPI: PCI Interrupt 0000:00:0b.0[B] ­> Link [LNKD] ­> GSI 10 (level, low) ­> IRQ 10
            ohci_hcd 0000:00:0b.0: OHCI Host Controller
            ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 2
            ohci_hcd 0000:00:0b.0: irq 10, io mem 0xe4000000
            usb usb2: configuration #1 chosen from 1 choice
            hub 2­0:1.0: USB hub found
            hub 2­0:1.0: 2 ports detected
            ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
            PCI: setting IRQ 11 as level­triggered
            ACPI: PCI Interrupt 0000:00:0b.1[C] ­> Link [LNKA] ­> GSI 11 (level, low) ­> IRQ 11
            ohci_hcd 0000:00:0b.1: OHCI Host Controller
            ohci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 3
            ohci_hcd 0000:00:0b.1: irq 11, io mem 0xe4001000
            usb usb3: configuration #1 chosen from 1 choice
            hub 3­0:1.0: USB hub found
            hub 3­0:1.0: 2 ports detected
            ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
            ACPI: PCI Interrupt 0000:00:0b.2[D] ­> Link [LNKB] ­> GSI 11 (level, low) ­> IRQ 11
            ohci_hcd 0000:00:0b.2: OHCI Host Controller
            ohci_hcd 0000:00:0b.2: new USB bus registered, assigned bus number 4
            ohci_hcd 0000:00:0b.2: irq 11, io mem 0xe4002000
            usb usb4: configuration #1 chosen from 1 choice
            hub 4­0:1.0: USB hub found
            hub 4­0:1.0: 2 ports detected
            usb 3­1: new full speed USB device using ohci_hcd and address 2
            ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
            ACPI: PCI Interrupt 0000:00:0b.3[A] ­> Link [LNKC] ­> GSI 10 (level, low) ­> IRQ 10
            ehci_hcd 0000:00:0b.3: EHCI Host Controller
            ehci_hcd 0000:00:0b.3: new USB bus registered, assigned bus number 5
            ehci_hcd 0000:00:0b.3: debug port 1
            ehci_hcd 0000:00:0b.3: irq 10, io mem 0xe4003000
            ehci_hcd 0000:00:0b.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
            usb usb5: configuration #1 chosen from 1 choice
            hub 5­0:1.0: USB hub found
            hub 5­0:1.0: 6 ports detected
            usb 3­1: unable to read config index 0 descriptor/all
            usb 3­1: can't read configurations, error ­110
            hub 5­0:1.0: over­current change on port 1
            hub 5­0:1.0: over­current change on port 2
            usb 3­1: new full speed USB device using ohci_hcd and address 4
            usb 3­1: configuration #1 chosen from 1 choice
            usb 3­2: new full speed USB device using ohci_hcd and address 5
            NET: Registered protocol family 8
            NET: Registered protocol family 20
            [ueagle­atm] driver ueagle 1.3 loaded

            usb 3­2: configuration #1 chosen from 1 choice
            usb 3­1: [ueagle­atm] ADSL device founded vid (0X1110) pid (0X9031) : Eagle III
            usb 3­1: reset full speed USB device using ohci_hcd and address 4
            usb 3­1: [ueagle­atm] using iso mode
            usb 3­1: [ueagle­atm] (re)booting started
            usbcore: registered new driver ueagle­atm
            Linux agpgart interface v0.101 (c) Dave Jones
            agpgart: Detected VIA Apollo Pro 133 chipset
            agpgart: AGP aperture is 64M @ 0xe0000000
            device­mapper: 4.6.0­ioctl (2006­02­17) initialised: dm­devel@redhat.com
            EXT3 FS on hda5, internal journal
            hdb: dma_intr: status=0x51 { DriveReady SeekComplete Error }
            hdb: dma_intr: error=0x84 { DriveStatusError BadCRC }
            ide: failed opcode was: unknown
            Adding 1293192k swap on /dev/hda13. Priority:­1 extents:1 across:1293192k
            kjournald starting. Commit interval 5 seconds
            EXT3 FS on hda14, internal journal
            EXT3­fs: mounted filesystem with ordered data mode.
            Supermount version 2.0.4 for kernel 2.6
            NTFS driver 2.1.27 [Flags: R/O DEBUG MODULE].
            NTFS volume version 3.1.
            NTFS volume version 3.1.
            NTFS volume version 3.1.
            NTFS volume version 3.1.
            NTFS volume version 3.1.
            NTFS volume version 3.1.
            NTFS volume version 3.1.
            NTFS volume version 3.1.
            NTFS volume version 3.1.
            NTFS volume version 3.1.
            loop: loaded (max 8 devices, max 1 partitions per device)
            hdc: ATAPI 48X DVD­ROM drive, 256kB Cache, UDMA(33)
            Uniform CD­ROM driver Revision: 3.20
            hdd: ATAPI 48X DVD­ROM DVD­R CD­R/RW drive, 2048kB Cache
            ACPI: Power Button (FF) [PWRF]
            ACPI: Power Button (CM) [PWRB]
            Using specific hotkey driver
            ACPI: CPU0 (power states: C1[C1] C2[C2])
            ACPI: Processor [CPU0] (supports 2 throttling states)
            Floppy drive(s): fd0 is 1.44M
            FDC 0 is a post­1991 82077
            end_request: I/O error, dev fd0, sector 0
            usb 3­1: [ueagle­atm] modem operational
            usb 3­1: [ueagle­atm] ATU­R firmware version : 44e2ea17
            ACPI: PCI Interrupt 0000:00:0a.0[A] ­> Link [LNKB] ­> GSI 11 (level, low) ­> IRQ 11
            NET: Registered protocol family 17
            CSLIP: code copyright 1989 Regents of the University of California
            PPP generic driver version 2.4.2
            NET: Registered protocol family 10
            lo: Disabled Privacy Extensions

            IPv6 over IPv4 tunneling driver
            [drm] Initialized drm 1.0.1 20051102
            ACPI: PCI Interrupt 0000:01:00.0[A] ­> Link [LNKA] ­> GSI 11 (level, low) ­> IRQ 11
            [drm] Initialized tdfx 1.0.0 20010216 on minor 0

            tu remarquera que la ligne ''modem operational '' est pr sente, et même que je voix mon modem se
            synchronis au d marrage (s' teindre, se rallumer puis se synchroniser)

            **** Bon pour ''/sbin/modprobe ­l ­t usb | grep usb''

            [root@localhost Desktop]# /sbin/modprobe ­l ­t usb | grep usb
            /lib/modules/2.6.17­5mdv/kernel/sound/usb/snd­usb­lib.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/sound/usb/snd­usb­audio.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/sound/usb/usx2y/snd­usb­usx2y.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/storage/usb­storage.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/ti_usb_3410_5052.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/keyspan_pda.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/digi_acceleport.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/anydata.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/airprime.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/whiteheat.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/visor.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/usbserial.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/safe_serial.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/pl2303.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/option.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/omninet.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/navman.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/mct_u232.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/kobil_sct.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/kl5kusb105.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/keyspan.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/ir­usb.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/ipw.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/ipaq.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/io_ti.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/io_edgeport.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/hp4x.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/garmin_gps.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/funsoft.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/ftdi_sio.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/empeg.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/cypress_m8.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/cyberjack.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/cp2101.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/belkin_sa.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/serial/ark3116.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/net/rndis_host.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/net/catc.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/net/asix.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/net/zaurus.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/net/usbnet.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/net/rtl8150.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/net/plusb.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/net/pegasus.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/net/net1080.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/net/kaweth.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/net/gl620a.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/net/cdc_subset.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/net/cdc_ether.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/mon/usbmon.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/misc/legousbtower.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/misc/cytherm.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/misc/auerswald.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/misc/uss720.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/misc/usbtest.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/misc/sisusbvga/sisusbvga.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/misc/usbled.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/misc/usblcd.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/misc/rio500.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/misc/phidgetservo.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/misc/phidgetkit.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/misc/ldusb.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/misc/idmouse.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/misc/emi62.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/misc/emi26.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/input/yealink.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/input/appletouch.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/input/acecad.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/input/xpad.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/input/wacom.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/input/usbtouchscreen.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/input/usbmouse.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/input/usbkbd.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/input/usbhid.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/input/powermate.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/input/keyspan_remote.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/input/kbtab.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/input/ati_remote2.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/input/ati_remote.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/input/aiptek.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/image/microtek.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/image/mdc800.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/host/ohci­hcd.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/host/ehci­hcd.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/host/uhci­hcd.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/host/sl811_cs.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/host/sl811­hcd.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/gadget/g_file_storage.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/gadget/g_ether.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/gadget/net2280.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/gadget/gadgetfs.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/gadget/g_zero.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/gadget/g_serial.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/core/usbcore.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/class/cdc­acm.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/class/usblp.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/atm/speedtch.ko.gz

            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/atm/cxacru.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/atm/xusbatm.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/atm/usbatm.ko.gz
            /lib/modules/2.6.17­5mdv/kernel/drivers/usb/atm/ueagle­atm.ko.gz

            **** Pour ''ps ­ef|grep eagle''

            [root@localhost Desktop]# ps ­ef|grep eagle
            root 1165 6 0 22:49 ? 00:00:00 [ueagle­atm]
            root 3476 3344 0 23:00 pts/0 00:00:00 grep ­­color eagle

            ****maintenant pour les commandes de la documentation :

            la commande ''tail ­f /var/log/messages | grep ueagle­atm'' ­­­> ne donne rien !

            et dans la section enregistrer les identifiants, je ne sais pas comment créer un fichier en root,
            il faut aussi créer un fichier Fichier /etc/ppp/peers/ueagle­atm

            je ne sais ni le créer , ni quoi mettre dedans , ni sont extension finale,

            je ne pence pas que sa soit comme dans windows (créer un fichier texte puis changer sont extension)

            sinon j'ai suivis la procdure normale pour créer une connection comme dans windows ou presque :
            nouvelle connection ­­> DSL ­­> Unknown/ADSL­USB Modem ­­> Wanadoo ­­> PPP sur ethernet (PPPoE) ­­> nom d'utilisateur et mot de passe et j'ai cocher autoriser les utilisateurs à gérer la connection puis sur connection au démarrage

            merci pour ton soutien.
            0
          2. neolux Auteur
            oups !

            **** pour ''lsmod'' :

            [root@localhost Desktop]# lsmod
            Module Size Used by
            ppp_async 9920 1
            ppp_generic 24628 1 ppp_async
            slhc 6784 1 ppp_generic
            crc_ccitt 2688 1 ppp_async
            tdfx 3168 2
            drm 62676 3 tdfx
            ipv6 237120 16
            snd_seq_dummy 3620 0
            snd_seq_oss 31392 0
            snd_seq_midi_event 7072 1 snd_seq_oss
            snd_seq 49488 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
            af_packet 17960 0
            snd_pcm_oss 40384 0
            snd_mixer_oss 16096 1 snd_pcm_oss
            snd_ens1371 22080 1
            gameport 11912 1 snd_ens1371
            snd_rawmidi 19936 1 snd_ens1371
            snd_seq_device 7212 4 snd_seq_dummy,snd_seq_oss,snd_seq,snd_rawmidi
            snd_ac97_codec 96868 1 snd_ens1371
            snd_ac97_bus 2848 1 snd_ac97_codec
            snd_pcm 70116 3 snd_pcm_oss,snd_ens1371,snd_ac97_codec
            snd_timer 19620 2 snd_seq,snd_pcm
            snd_page_alloc 8712 1 snd_pcm
            snd 46500 12
            snd_seq_oss,snd_seq,snd_pcm_oss,snd_mixer_oss,snd_ens1371,snd_rawmidi,snd_seq_device,snd_ac
            97_codec,snd_pcm,snd_timer
            soundcore 8096 1 snd
            floppy 55172 0
            video 13924 0
            thermal 11240 0
            processor 21448 1 thermal
            fan 4036 0
            container 3968 0
            button 5808 0
            battery 8260 0
            ac 4292 0
            ide_cd 35776 0
            binfmt_misc 9800 1
            loop 15400 0
            nls_utf8 2624 10
            ntfs 266940 10
            supermount 34128 1
            dm_mod 49944 0
            via_agp 8896 1
            agpgart 27240 2 drm,via_agp
            ueagle_atm 23048 0
            usbatm 16480 1 ueagle_atm
            atm 37108 1 usbatm
            ehci_hcd 29160 0
            ohci_hcd 19012 0
            uhci_hcd 20748 0
            usbcore 113472 6 ueagle_atm,usbatm,ehci_hcd,ohci_hcd,uhci_hcd
            tsdev 7040 0
            evdev 8864 1
            ext3 124936 2
            jbd 51028 1 ext3
            0
        4. neolux Auteur
          j'ai bien suivi tous ce qui a été mentionné sur la page :
          http://remi.collet.free.fr/index.php?2006/02/24/113-configuration-du-pilote-ueagle-atm

          Jusqu'au moment de configurer ma connexion PPPoE :
          Quant je rentre la commande ''modprobe br2684'' sa ne fait rien, sa veux surement dire que c'est déjà
          charger, Sinon pour ''br2684ctl ­b ­c 0 ­a 0.35'' sa me fait ''command not found'' !

          [root@localhost Desktop]# modprobe br2684
          [root@localhost Desktop]# br2684ctl ­b ­c 0 ­a 0.35
          bash: br2684ctl: command not found

          je ne comprend pas puisque j'ai bien installé tous ce qui est en rapport avec atm dont ''liblinux,atm1-2,4,1­9mdk''
          (qui n' tais pas installer au paravent)

          Peut-être qu'il faut recompiler tout sa !!?? (je doit alors installé le kernel­source),

          Merci tufs de ton soutien.
          0
          1. tufs Contributeur
            re

            Bon je vais faire comme si je voulais l installer mais le problem c est que j ai pas le modem bref ....

            tufs@debian:~$ su -
            Password:
            debian:~# cd /lib/firmware
            debian:/lib/firmware# tar xvzf /home/tufs/ueagle-data-1.1.tar.gz
            ueagle-data-1.1/
            ueagle-data-1.1/930-fpga.bin
            ueagle-data-1.1/adi930.fw
            ueagle-data-1.1/CMV9i.bin
            ueagle-data-1.1/CMV9p.bin
            ueagle-data-1.1/CMVei.bin
            ueagle-data-1.1/CMVeiWO.bin
            ueagle-data-1.1/CMVep.bin
            ueagle-data-1.1/CMVepES03.bin
            ueagle-data-1.1/CMVepES.bin
            ueagle-data-1.1/CMVepFR04.bin
            ueagle-data-1.1/CMVepFR10.bin
            ueagle-data-1.1/CMVepFR.bin
            ueagle-data-1.1/CMVepIT.bin
            ueagle-data-1.1/CMVepWO.bin
            ueagle-data-1.1/DSP9i.bin
            ueagle-data-1.1/DSP9p.bin
            ueagle-data-1.1/DSPei.bin
            ueagle-data-1.1/DSPep.bin
            ueagle-data-1.1/eagleI.fw
            ueagle-data-1.1/eagleII.fw
            ueagle-data-1.1/eagleIII.fw
            debian:/lib/firmware# mv ueagle-data-1.1 ueagle-atm
            debian:/lib/firmware# cd
            debian:~# tail -f /var/log/messages | grep ueagle-atm
            Lors de la connexion du modem, vous devez obtenir
            moi je n ais pas le modem OK

            pour cree le fichier /etc/ppp/chap-secrets ou alors le fichier
            /etc/ppp/peers/ueagle-atm ==>

            # gedit /etc/ppp/chap-secrets

            # gedit /etc/ppp/peers/ueagle-atm

            tu auras l ouverture d une fenetre tu tapes se qu il faut tu enregistres et tu quittes <<< ok et ton fichier est cree ....

            ps : tu ne dois pas recopier tout ce qui est noter sur le tutoriel
            voir FAI avant ...et bien reflechire avant de taper !!!

            si tu sais pas repost avec fournisseur d acces etc etc .....
            0
            1. neolux Auteur
              enfin j'ai résolu mon problème, et sa grasse @ mes confrère du site https://www.forumdz.com/

              (Merci @ ostenx et @ JoestaRR)

              Pour installer le sagem fast 800 sous la mandriva 2007, j'ai installer ces fichiers :

              ppp-pppoe-2,4,3mdv2007,0,i586,rpm
              linux-atm-libs-2,5,0-1,20050118cvs,i386,rpm
              linux-atm-2,5,0-33,i586,rpm

              vous trouverais plus d'info sur cette page :
              https://www.forumdz.com/showthread.php?t=5818&page=4&highlight=mandriva+2007

              Merci tufs de m'avoir aidé,
              0
              1. coco
                bonjour, comment tu as telechargé

                ppp-pppoe-2,4,3mdv2007,0,i586,rpm
                linux-atm-libs-2,5,0-1,20050118cvs,i386,rpm
                linux-atm-2,5,0-33,i586,rpm
                et merci
                0

                Discussions similaires

                Erreur 3005 sur France TV
                Cambodgil

                6 réponses
                Télécharger fast and furious 1,2,3,4,5
                cooljasonkiller

                3 réponses
                Problème streaming France 2
                95 indomptable

                1 réponse
                Erreur s3 bbox wifi 7 bouygues
                Fido62

                14 réponses
                Erreur code 4001
                contrariness

                1 réponse