My logicom riva 250 displays searching

At LOGICOM, they are very reluctant to respond... so here's how to solve this problem for which I haven't read the solution on the forums:

After many futile attempts... on my LOGICOM ILOA 3500 phone

LINKING A HANDSET WITH A BASE

Access to this function requires knowledge of the base's PIN code (0000 by
default).
A base can register up to 6 handsets.
To register a handset to a base, follow these steps:
On the base:
* Press and hold the bottom button on the base (large dot + 3 small curves) for 10 seconds
* The base is in pairing mode for 3 minutes, now follow the steps to be done on the handset.
On the handset to be registered:
* Press the OK button at the top left of the handset
* “JOURNAL” appears on the screen
* Use the large button under the screen that allows you to scroll up and down to select “ASSOCIATION”
* Press the OK button
* Use the large button under the screen that allows you to scroll up and down to select the base to which the handset should be registered.
* Press the OK button
(not necessary here as it is the corresponding base for the handset, so direct to the next step)
* “PIN ? ----” appears on the screen.
* Use the alphanumeric keypad to enter the PIN code of the base (0000 by
default) on which this handset will be registered
* Press the OK button
* “CHERCHE” appears on the screen.
* A beep informs you that the handset has been registered to the base.
8- RESET

If necessary, reset to default if you make a mistake.

Hello! No need to stress about it any further!!!

I have the same problem with my Riva Pop 450 phone... it says "searching" on the handset and keeps beeping... Help.... what is causing this?

Hello,

My phone is the Riva 200. When I take it off the base and make a call, there is no dial tone, and when someone calls me, I can answer, but I can hear the other person, and they can't hear me.
**help**

Hello
mine shows canceled;... I can't associate it with my database. Could you please help us!!!
I have model 200

Logicom Riva 250 worked and then the message 'Searching' appeared on the screen.
I tried unplugging/replugging, attempting a factory reset, but despite these actions, I am getting no results. The 'Searching' message is still flashing.
Thank you for your help.

Well, never mind, I found it. It's really simple; you just need to think about putting the batteries in the handset :p
(In the next version, they should display "BATTERY" instead!!!)

I have the same problem.
Logicom Riva 250 purchased on Friday. When I plugged them in, the message 'Searching' appeared on the screen.
I tried unplugging/replugging, attempting pairing, and factory resetting, but despite these attempts, I am getting no results. The message 'Searching' is still blinking.

Sincerely,
Marsupio

Is it normal for the dial on my RIVA 450 handset not to light up? It's not very readable without light and it says "color screen" in the product description.
Thank you

YOU NEED TO CONNECT THE PHONE TO THE BASE

Hello,
I have solved the problem
the explanation of the procedure to follow is on pages 33 and 34 of the user manual
best wishes

Good evening,

I have provided the complete procedure in this forum to solve the problem concerning the LOGICOM ILOA 3500 as that is the one I have, here it is again:
At LOGICOM, they are not willing to respond... so here is how to solve this problem for which I have not read the solution on the forums so:

After many futile manipulations... on my LOGICOM ILOA 3500

PAIRING A HANDSET WITH A BASE

Accessing this function requires knowing the base's PIN code (0000 by
default).
One base can register up to 6 handsets.
To register a handset on a base, follow these manipulations:
On the base:
* Press and hold the bottom button of the base (big dot + 3 small curves) for 10 seconds
* The base is in pairing mode for 3 minutes, now follow the manipulations to be done on the handset.
On the handset to be registered:
* Press the OK button at the top left of the handset
* "LOG" appears on the screen
* Use the large button below the screen that allows you to scroll up and down to select "PAIRING"
* Press the OK button
* Use the large button below the screen that allows you to scroll up and down to select the base to which the handset should be registered.
* Press the OK button
* (not necessary here because it’s the corresponding base of the handset, so go directly to the next step)
* "PIN? ----" appears on the screen.
* Use the alphanumeric keypad to enter the PIN code of the base (0000 by
default) on which this handset will register
* Press the OK button
* "SEARCH" appears on the screen.
* A beep informs you that the handset has been registered on the base.
8- RESETTING

If necessary, reset to default if you make a mistake.

Hi! No need to complicate things further!!!

Hello,
I have the same problem, yet the batteries have been charged for 24 hours
For it to work, it seems that the base must always be plugged into a power outlet, otherwise, subscriber absent
Is there another solution, or is it a general problem?

My Logicom Riva 250 is constantly busy. When I call my number, I reach my voicemail. What should I do? Thank you for your help.

For the telephone to work, make sure it stays plugged into a power outlet.

Bonjour, mon téléphone Riva Pop 252 affiche "cherche" en clignotant. Je ne comprends pas ce qu'il faut faire. J'ai déjà tout débranché et rebranché, mais rien ne change. Merci de m'aider.

Good evening, I have an issue with my Logicom Riva Pop 250; it no longer displays anything, the batteries are charged, but apparently it no longer recognizes the base. I don't know how to fix it, knowing that I can't use the keyboard as it is blocked and none of the keys work anymore.
Thank you.

I have the same problem. Help! Thank you.

receive responses to remove search on the logocom

the phone must always be plugged into a power outlet

I have the same problem, but intermittently
depending on the location, depending on the weather, the system works properly or breaks down again
I suspect the batteries but without certainty
to be continued ???