Wifi Peekbox 4

Hello, yes applicable solution like for me.
To ensure already it is necessary to:
the wifi ssid (router or freebox)
then the key (if there is one)
in the network settings you need to choose wired or wifi
auto ip address

On the wifi settings side, you need to check:
if the channel is the same as that of the router (otherwise switch to auto)
make sure if it’s wep or not for the network key

It’s after in run (windows: I did a "cmd"
to do a ping test (for the ip address of the peekbox 4)

ping 192.168.0.?? < IP to my Peekbox

Sending a 'ping' request to 192.168.0.10 with 32 bytes of data:

Reply from 192.168.0.10: bytes=32 time<1ms TTL=128
Reply from 192.168.0.10: bytes=32 time<1ms TTL=128
Reply from 192.168.0.10: bytes=32 time<1ms TTL=128
Reply from 192.168.0.10: bytes=32 time<1ms TTL=128

Ping statistics for 192.168.0.??: < IP to my Peekbox
Packets: sent = 4, received = 4, lost = 0 (loss 0%),
Approximate round trip times in milliseconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms

Additionally, it is necessary to install the network protocols: (page 177 of 446 pdf file)
NWlink IPX/SPX/NETBIOS
it is necessary to look for the guests (page 179 of 446 pdf file)
The last network protocol: (page 181 of 446 pdf file)
NETBEUI

Hello,

Are you satisfied with your PeekBox?
I read that you cannot copy files to the PeekBox via Wi-Fi, is that true?

I am looking for the documentation in PDF format, can someone send it to me?
My email: stephnews2 at gmail.com

Thank you in advance.

Salut, tu peux trouver la documentation sur le CD fourni avec la Peekbox.

Hello everyone,

I have a Peekbox 4 with Wi-Fi connected to 3 PCs running Vista (ouch, ouch)

Despite all my efforts, I am unable to communicate between the Peekbox and the PCs.
(Wi-Fi APP successfully set up on Peekbox)

In CMD, the Ping command on my Peekbox works well with good response times.

I think it must be a sharing issue.

Regarding sharing (all my PCs communicate well with each other. Guest mode activated + permissions OK on PCs)
Firewall disabled on Vista as well as on the FreeBox router

I really don't understand what's wrong.

Could it be due to the fact that Vista doesn't have NetBeui capability (provided on the Peekbox CD for XP) which would render the Wi-Fi mode incompatible with Vista?

Ps: Let’s hear it, gentlemen, I’m waiting for your brains to help me out :p

It would be a shame for this peekbox to only work with netbeui.
It is likely that it should work with IP, maybe activate netbios on tcpip.
--

and ... There you go!

Hello
petition peekbox 4 for firmware improvements
https://www.mesopinions.com/petition/

Sign this petition for PEEKTON to stop treating us like fools, the more of us there are, the better our chances of making a change!!!!

It's simple, just click here => https://www.mesopinions.com/petition/

Thank you for forwarding this petition:
https://www.mesopinions.com/petition/

Here is Peekton's response regarding the impossibility of getting the Peekbox 4 to appear in Windows Vista:

Hello,

Your network configuration does not depend on the operating system of the computers connected to it.

However, access to certain information may vary depending on your equipment.

To connect your Peekbox 4 to your home network, you need to check the following points:

SETUP > NETWORK: AVAILABLE: WIRELESS
IP CONFIG: MANUAL
IP ADDRESS: 192.168.1.3 (the last digit is the number you assign to the Peekbox on the network)
NETWORK MASK: 255.255.255.0 (most often)
GATEWAY: 192.168.1.254 (254 or 1, this is the IP address of the router on the network)

SETUP > WIRELESS: ESSID: your network name (respecting uppercase and other characters)
CHANNEL: the channel number used by the router
WIFI SECURITY: AUTOMATIC
WEP ENCRYPTION: WEP (if you are using a WEP key with your network)
WEP KEY: enter your WEP key here (if necessary)
WIFI APP: press ENTER to connect the Peekbox to the network.

If the SUCCESS message appears, your Peekbox is connected.
If the FAILURE message appears, try connecting by disabling WEP encryption on your Wifi network.

If you are unsure of the IP configuration you entered, you can make an Ethernet connection in Auto mode to ensure the addresses are correct. Then keep the automatic configuration while only changing the "wireless" availability.

You can check the connection of your Peekbox from your PC:

Start > Run and type "cmd" then Enter.
Then, in the black window, type: ping 192.168... (IP address of your Peekbox on the network).

If all ping packets are received correctly, then your Peekbox is connected to the network.

Folders must be shared from your computers and accessible to guests.

Then you need to perform a "REFRESH" from the navigation menu of your Peekbox.

Feel free to contact us by phone at 0820.03.03.03 for more information.

However, if despite these checks, your Peekbox does not connect to your network, it may be defective.

Bonjour,
Hello, I have a problem that if I type in my SSID I cannot use the sign "_" but that is part of my SSID. What can I do?

Sorry for not speaking and writing in French.

However, it is important to be aware that it is impossible to access the PEEKBOX 4 via WIFI from your PC.
The manufacturer has not implemented the NDAS system, in other words, the ability to transfer/delete/modify files via wifi or ethernet port... Q.E.D.
For more information, you can visit the following forum:
https://forum.hardware.fr/hfr/VideoSon/Materiel/topic-peekbox-peekton-sujet_99464_1.htm

or consult the online petition (and even sign it...):
https://www.mesopinions.com/petition/

I think you will understand a lot of things and the justification for our actions towards Peekton...

Hoping to count you among us!!!

Thank you very much PATATE34....but I don't understand French very well and I don't understand your message... do you speak English, German or Spanish??????

Bonjour,
vous devez changer votre Essid et supprimer le signe "_", car vous ne pouvez pas utiliser ce symbole avec votre PB4. Désolé...
D'autre part, vous devez être conscient qu'il est impossible d'atteindre le PEEKBOX 4 en WIFI depuis votre PC.
Le système de fabrication NDAS ne l'a pas implémenté, en d'autres termes, vous ne pouvez pas transférer/supprimer/mette à jour les fichiers via le wifi ou le port Ethernet... .
Pour plus d'informations, vous pouvez consulter le forum suivant (uniquement en français désolé) : https://forum.hardware.fr/
ou consulter la pétition en ligne (et même la signer...) :
https://www.mesopinions.com/petition/
Je pense que vous comprendrez beaucoup de choses et la justification de nos actions chez Peekton...

Merci patate34 pour ton aide, je pensais à changer le SSID et je pense que je devrais le faire. Mais y a-t-il des informations sur Peekton concernant un nouveau firmware ? Je ne peux pas le trouver sur leur page. Le problème, c'est qu'en outre, je ne peux pas taper la clé WEP parce que la Peekbox n'autorise pas les touches de G à Z... c'est le prochain problème... où puis-je trouver une mise à jour du firmware ? Merci pour ton aide.

Le correctif 1.1.19 est disponible à ce lien :
http://www.megaupload.com/?d=8QGV0LC2

Cordialement.

Salut patate,

merci beaucoup pour ton aide...je suis vraiment content de cela. Sais-tu si la mise à jour du firmware résoudra les problèmes que j'ai ?

rainer

Je ne sais pas, Peekton n'a rien dit à propos du 1.1.19... Tu dois écrire au support de Peekton à info@peekton.com...
Bonne chance !

Bonjour Patate,

Merci encore pour votre aide....je suis toujours désespéré :

La Peekbox est maintenant connectée au routeur (Zyxel), qui affiche le menu Peekbox "sans fil réussi".

Mais maintenant, j'ai le problème que je ne peux pas voir la Peekbox dans l'environnement réseau. Elle n'apparaît pas lorsque je la cherche sur le réseau depuis mon ordinateur portable qui est également sur le réseau... peut-être que vous connaissez le problème et pouvez m'aider à nouveau...

Rainer