Parabola with 2 LNBs (HOTBIRD AND ASTRA)

J'ai un démodulateur géant 9800 HD, il fonctionne très bien avec une parabole individuelle, mais il ne fonctionne pas avec une parabole collective. Merci d'avance.

I think Astra is located on the right or left, don't move the dish, you have two LNBs, try to put the bracket on the other LNB without moving the dish, you might also have an issue with your LNB switching and that can be resolved at the receiver level by activating, for example, the Diseqc function.

You need to choose the same DiSEqC for both in the search parameter settings, but two different ports (otherwise you'll only get one satellite). See you!

Good evening, I think the antenna needs to be changed. I have the Visiosat Bisat antenna and the dual-head mount, and it works very well; you can even add a third head for three satellites or even more. You should check Visiosat.

It requires a parabola of at least 80 centimeters.

Hotbird is more difficult to position; start by aiming your dish towards Astra 19. Once you have positioned Astra, Hotbird becomes easier. You adjust the elevation and move your dish to the right. You can see the direction of the satellite from the link below http://www.dishpointer.com/ but with your address and the satellite you want, you will get the position of your satellites. You can contact me at email address removed Moderation CCM

@lenaturel I downloaded the app on my iPhone, it's amazing!!!

Hello, I need help, I have an 80 cm satellite dish and a dual LNB, but I can't get Hotbird and Astra at the same time; I can only get one or the other. I usually find HB and then automatically Astra.

What is the problem or rather the solution, please?

Is it in the configuration of the receiver, or did I configure it with 2 satellites via DiSEqC A/B with Hotbird on DiSEqC AA for HB and AB for Astra?

THANK YOU

Hello,
I have a problem: on my receiver, while trying to catch Hotbird, I have a signal strength of 70% but the signal quality is 0 and doesn't change. Thank you for your help.

If the installation of 2 satellites or 1 dual satellite dish / Diseqc switch 1 or monobloc 6° Diseqc, Astra - Hot-Bird, has been carried out and configured properly with Diseqc A-B according to best practices, and is not affected by a failure or misalignment, everything is working nominally.

Check your setup & equipment and in the receiver menu, the Diseqc assignments, generally A = Astra and B = Hot-Bird

+ Google: " satellite reception diagnostic help "

Hello,

I have a satellite dish of about 80cm with a single-block LNB and one output, Astra 6° and Hotbird with integrated DiSEqC 2.0. I get Hotbird very well but not Astra.
Could you please give me some advice?

The decoder is the one from Orange TV;
I receive Hotbird with DiSEqC off and on DiSEqC A.

Thank you

Anis

Hello, are you properly connected to the internet? If not, turn off the power for 10 seconds, then turn it back on. Normally, you should recover the channels.

It should be noted that an Orange TV terminal has never been multisat (1 satellite of choice out of 3) and, in any case, the Orange bouquet (then on Hotbird) is more than distributed via Astra 1. The same will apply to Bein Sports, or even Bis TV, which are refocusing, additionally on Eutelsat 5WA.

The Diseqc 1.0 of a terminal is backward compatible with Mini-Diseqc A-B (tone impulse) from a switching accessory with 2 inputs, or a Diseqc switch with 1 to 4 inputs.

To control 5 inputs (5 lnb heads) or more, the decoder must include Diseqc 1.1 or even Diseqc 1.2 or 1.3 for a multi-sat motorized antenna...

To simplify the approach, we assign A or 1 or 1 of 2 or the default Diseqc to Astra 1.

Finally, for receiving Astra and Hot Bird on a common dish, there are 2 solutions: 2 separate heads ( > 70 cm ..1.20....1.80 m ...) on an adjustable head support or 1 monobloc head (only 80 cm), which is the economical choice.

The technical choice:
http://img110.xooimage.com/files/0/9/c/hotbird-astra-mul...t-diseqc-5070c87.jpg

Here is the choice of a canal-ready labeled model for canalsat with a compatible model from 2017, see the restrictive list of only terminals from 2017, given the change in standard, which does not concern Tntsat.