erreur systeme e000 canon ir 1600 Résolu/Fermé

Question

bonsoir, j'ai une photocopieuse canon ir 1600 qui m'affiche après nettoyage ERREUR SYSTEME E000, à bout de souffle suis-je SOS, SOCORO.

Eureca · Accepted Answer

Le code E000 corespond a un probleme au niveau de l'unité de fixation qui se trouve sur la gauche du copieur. 
Le probleme majeur est que l'unité n'est pas alimenté pour qu'il se mette en chauffe, ou que la resistance chauffant le rouleau de fixation est H/S, ou alors que la partie electrique est H/S. 
Sinon, si c'est juste un bug, il faut enlever le code erreur dans le mode SAV, quoi qu'il en soit, il faudra en lever le code erreur au bout du compte. 

Ciao a +.

dododo · Answer

moi aussi j'ai le même probleme

ploqui · Answer

·	Check all doors are fully shut including the lower left door.
Go into service mode by pressing * then #. 
·	Use left and right keys and find “printer”.
·	find “reset printer”. 
·	Confirm yes to “reset printer”
·	switch OFF for 5 seconds and ON again

It works for me.

Good luck

prince matouzebi · Answer

Bonjour, 
salut j'ai un problème avec ma machine ir 1600 car elle m'affiche le code e001

yaro · Answer

Bonjour, 
salut, moi mon problème est ma machine photocopieur canon ir 2000 qui m'affiche le code: erreur syeteme E 000.
Merci de me repondre.

Oumby · Answer

salut
j'ai un photocopieur canon  IR 1018 qui quand je lance la copie après lecture ne copie pas et maffiche un message  erreur système E 808 merci de me dire ce que je dois faire

vigilatus · Answer

Bonjour je suis coincé et j'ai un boulot fou à faire avec mon copieur au bureau. il m'affiche le message d'erreur E019 et le voyant rouge s'allume. Comment dois puis je résoudre ce problème.

gypsoul · Answer

J'ai essayé cette atuce de l'ami ploqui qui a marché pour l'erreur système E000; Je conseil donc à nos amis ayant le même prloblème de l'essayer.

Mer Mr ou Mrs Ploqui (thank you very much for your help...)


 Check all doors are fully shut including the lower left door. 
Go into service mode by pressing * then #. 
· Use left and right keys and find “printer”. 
· find “reset printer”. 
· Confirm yes to “reset printer” 
· switch OFF for 5 seconds and ON again 

It works for me. 

Good luck

CHERKI · Answer

salut tout le monde j'ais un problème avec une photocopieuse canon ir1605 je croi que c'est a couse d'un choc éléctrique quant je l'alume il me donne erreur système e000.
ya t'il une solution pour cette panne . je remercier d'avance tout qui me donne une solution merci

faell · Answer

Bonjour, j'ai ai travail une CANON iR1610 qui a eu une erreur E000. Le dépanneur est venu ce matin, et ça signifie qie le four de la photocopieuse est mort (le four permet à temperature élevé de fixer l'encre). En gros, y a rien à faire sauf le changer...passe le message...bon courage (et à ton prote feuille aussi)

erreur systeme e000 canon ir 1530 · Answer

salut j'ai un problème avec ma machine PHOTOCOPIEUR ir 1530 SA FFICHE  ERREUR SYSTEME E000

chapy · Answer

svp ma ir 2016 affiche àl'allumage erreur e007 veillez me donner la demarche à suivre pour résoudre le probleme

eddythedove · Answer

svp veuillez aussi m'envoyer les solutions pour les codes d'erreu de e000 à e007. merci d'avance
Eddythedove

mjcanon · Answer

bjr beaucoup j'ai une probleme sur les copieurs digital IR la ou je rancotre souvant ds codes Erreur systeme E 019
j'ai besoin votre aide 


mercie beaucoup

syphax · Answer

sslt voila les solutions pour les codes d'erreu de e000 à e007
E000	La lecture principale de thermistance n'atteint pas 40 o C 14 sec après que le réchauffeur de réparation continue (erreur de réparation de basse température)
E001	La lecture principale de thermistance atteint 220°C ou plus haut (erreur à hautes températures de réparation)
E002	A start-up fault is detected under any of the following conditions of the main thermistor (start-up detection fault):
after exceeding 40°C, it fails to reach 60°C within 10 sec.
after exceeding 60°C, it fails to reach 80°C within 10 sec.
. . .
after exceeding 180°C, it fails to reach 195°C within 10 sec.
E003	After the end of the WAIT period, the main thermistor reading is 100°C or lower. In standby, the sub thermistor reading is 50°C or lower. (low temperature error in fixing temperature control)
E004	At time of initialization, the ZEROXI* signal of the power supply is not detected.
During temperature control, the ZEROXI* signal does not arrive for 3 sec continuously.
A short circuit is detected in the triac (ASIC; fixing temperature control drive circuit error).
Possible cause: Fixing assembly is faulty. (The main thermistor has an open circuit. The sub thermistor has an open circuit. The fixing heater has an open circuit. The power supply PCB is faulty. The DC controller PCB is faulty.)
Note: If E000 through E004 is indicated, the RAM on the image processor will retain the error memory of the fixing assembly after the power switch has been turned off an then on. Execute the following in service mode, and turn off and then on the power switch to clear the memory:
#7 PRINTER - #4 PRINTER RESET - YES=(*)
E010	A specific revolution is not detected from the main motor rotation detection signal (MLOK*), causing the signal to go '1' (main motor fault)
Possible cause: The main motor (M101) is faulty. The controller PCB is faulty.
E100	When the scanner motor is started up, the BD input signal does not arrive within a specific period of time.
When the scanner motor is started up, the motor rotation is too fast, and fails to reach a specific revolution within 20 sec at time of deceleration.
While the scanner motor is rotating at a specific speed, the BD input signal cycle is not within a specific range (±2%) for an equivalent of 10 mm (print distance).
While the scanner motor is rotating at a specific speed, the BD input signal cycle is not as indicated (±2%).
During the WMUPR period after the power switch has been turned on or the front cover/left cover has been opened/closed, the drum unit is absent.
Possible cause: The wiring is faulty (short circuit, open circuit). The laser scanner unit is faulty. The DC controller PCB is faulty. The drum unit is not installed.
E719	The communication between the card reader and the image processor PCB is disrupted.
Possible cause: The wiring is faulty (short circuit, open circuit). The card reader is faulty. The image processor PCB is faulty.
Note: If E719 is indicated, the fault in communication is retained by the RAM on the image processor even when the power switch has been turned off and then on; be sure to execute #12 CLEAR - CARD in service mode before making corrections.
E805	After the heat discharge fan drive signal is generated, the fan lock detection signal does not arrive for a specific period of time.
Possible cause: The fan wiring is faulty (short circuit, open circuit). The heat discharge fan (FM101) is fautly. The DC controller PCB is faulty.
Finisher Error Codes
E500	An error has occurred in the communication between the machine and the finisher twice continuously.
Possible cause: The harness to the finisher is faulty (disconnected connector, open circuit). The finisher controller PCB or the DC controller PCB is faulty.
E514	The stack delivery belt does not reach home position when the stack handling motor (M2) is driven for a specific time (CW; if the same condition occurs during stack delivery, a jam will be identified).
Possible cause: The stack handling motor (M2) is faulty. The stack delivery home position sensor (S8) is faulty. The connector is disconnected or has an operation circuit. The stack handling motor relay harness is faulty. The stack delivery belt is faulty. The finisher controller PCB is faulty.
E530	The rear aligning plate does not reach home position when the rear alignment motor (M4) has been driven for a specific time.
The rear aligning plate does not reach home position when the rear alignment motor (M4) has been driven for a specific time.
Possible cause: The rear alignment motor (M4) is faulty. The rear aligning plate home position sensor (S7) is faulty. The sensor connector is disconnected or has an open circuit. The rear alignment motor relay harness is faulty. The rear aligning plate is subjected to an abnormal load. The finisher controller PCB is faulty.
E531	The stapler does not leave the stapling home position sensor (S13) within 0.5 sec after the stapler motor (M6) is rotated CW.
The stapler does to return to the home position sensor (S13) within 0.5 sec after the stapler motor (M6) is driven CW and, in addition, it does not return to the sensor within 0.5 sec after the motor is driven CCW thereafter.
Possible cause: The stapler motor (M6) is faulty. The stapler home position sensor (SW1) is faulty. The stapler harness is faulty. The finisher controller PCB is faulty.
E537	The front aligning plate does not reach home position when the front aligning motor (M3) is driven for a specific time.
The front aligning plate does not leave home position when the front alignment motor (M3) is driven for a specific time.
Possible cause: The front alignment motor (M3) is faulty. The front aligning plate home position sensor (S6) is faulty. The sensor connector is disconnected or has an open circuit. The front alignment motor relay harness if faulty. The front aligning plate is subjected to an abnormal load. The finisher controller PCB is faulty.
E551	The delivery fan rotation signal (FNALCOK) does not arrive within 1 sec when the heat discharge fan drive signal (FANON) is sent.
Possible cause: The heat discharge fan (FM1) is faulty. The heat discharge fan relay harness is faulty. The heat discharge fan is subjected to an abnormal load. The finisher controller PCB is faulty.
E577	The return roller does not reach home position when the delivery motor (M1) is driven for a specific time. (If the same condition is detected while alignment takes place in the direction of feed, a jam will be identified)
Possible cause: The delivery motor (M1) on the finisher controller PCB is faulty. The return roller home position sensor (S3) is faulty. The connector is discontented or has an open circuit. The delivery motor relay harness is faulty. The return roller is faulty. The finisher controller PCB is faulty.
E580	The stack tray upper limit sensor (S1) goes ON while the stack tray up/down motor (M5) is in operation.
The clock signal of the stack tray up/down clock sensor (S9) is not detected 15 times or more within 0.8 sec while the stack tray up/down motor (M5) is in operation.
It does not reach the stack tray paper height sensor (S10) 2 sec after the stack tray up/down motor (M5) rotates for ascent.
It does not leave the stack tray power height sensor (S10) 2 sec after the stack tray up/down motor (M5) starts to rotate for descent.
Possible cause: The stack tray up/down motor (M5) is faulty. The stack tray paper height sensor (S10) is faulty. The sensor connector is disconnected or has an open circuit. The stack tray up/down clock sensor (SW9) is faulty. The sensor connector is disconnected or has an open circuit. The stack tray up/down motor is subjected to an abnormal load. The finisher controller PCB is faulty.
E585	The stack retaining lever does not reach home position when the stack handling motor (M2) has been driven for a specific time (at the start of motor CCW rotation). (If the same condition is detected during stack delivery, a jam will be identified)
Possible cause: The stack handling motor (M2) is faulty. The stack delivery lever home position sensor (S8) is faulty. The sensor connector is disconnected or has an open circuit. The stack handling motor relay harness is faulty. The stack retaining lever is faulty. The finisher controller PCB is faulty.


Canon iR2016 / iR2016J / iR2016i / iR2020 / iR2020i 
&#1050;&#1086;&#1076; &#1086;&#1096;&#1080;&#1073;&#1082;&#1080;	&#1057;&#1091;&#1073;&#1082;&#1086;&#1076;	&#1054;&#1087;&#1080;&#1089;&#1072;&#1085;&#1080;&#1077;
E000	0000	Fixing temperature abnormal rise
E001	0000	Fixing unit temperature rise detection (by main thermistor)
	0001	Fixing unit temperature rise detection (by sub thermistor)
E002	0000	Fixing unit temperature insufficient rise
E003	0000	Low fixing temperature detection after standby (by main thermistor)
	0001	Low fixing temperature detection after standby (by sub thermistor)
E007	0000	Fixing film rotation error
E010	0000	Main motor rotation error
E019	0001	Waste toner full detection
	0002	Waster toner full detection sensor failure
E052	0000	Duplex unit connection error
E100	0000	BD cycle out of range
E197	0000	Erroneous communication with printer engine
E500	0001	Finisher communication error
E520	0000	Offset error
E531	0000	Stapling error
E540	0001	Paper surface not detected (standard tray)
	0002	Not moved within the specified time (standard tray)
	0003	Sensor not reached within 3 seconds (standard tray)
	0005	Encoder clock failure (standard tray)
E542	0001	Paper surface not detected (optional tray)
	0002	Not moved within the specified time (optional tray)
	0003	Sensor not reached within 3 seconds (optional tray)
	0005	Encoder clock failure (optional tray)
E575	0000	Stack delivery error
E584	0000	Shutter failure
E716	0000	Erroneous communication with optional cassette
E719	0000	Erroneous communication with card reader (serial communication)
	0002	Erroneous communication with coin vender (serial communication)
E733	0000	Erroneous communication between controller and printer
E736	0000	CCU communication error
E739	0000	Erroneous communication between controller and network board
E744	0001	Language file/boot ROM/USB memory error
	0002	
	0003	
	0004	
E805	0000	Fan failure
E808	0000	Fixing drive circuit failure

togacom · Answer

bonsoir...j'ai ce probleme d'erreur systeme E100 apres le netoyage...quelq' un peut m'aider....?merci

wahid · Answer

salut j'espere t'aider dans ton probleme
le code erreur systeme E000 c'est pour le nettoyage iessay de nettoyer le ventillateur qui se trouve deriere l'apareil tu le soufle avec un compresseur

zeus2185 · Answer

svp veuillez aussi m'envoyer les solutions pour les codes d'erreu de e000 à e003, merci de me les envoyer

hopkins69 · Answer

bsr mes confrere j'ai lu toute les  question  de votre  prb d'erreur e000 sur le copieur canon ir 1600 et d'autre series voila  votre  probleme d'erreur  
  
- Contact élément chauffant oxydé ou grillé.
- Elément chauffant (H1, H2 ou H3) défectueux.
- Fusible grillé.
- Thermistance TH1 (Mauvais contact ou câble sectionné).
- Thermocontact ouvert.
- Carte de puissance C.A/ S.S.R. ou Triac Q1 défectueux.
- Carte de commande défectueuse.  

et pour d'autre  code voila  le  bon liens  a voire :  http://copieurs.free.fr/canon/codepancop.htm 

d'autre  question suis  a votre dispostion   hopkins69

hopkins16 · Answer

Bonsoirs à tous, pour  le code E000 de canon IR 1600 Voila la solution Il faut 'simplement nettoyer votre copieurs tout simplement  Je suis a votre disposions  contacté moi o  forum bon chance

mohaicha · Answer

bj j'ai une photocopieur canon ir1605 le pb c'est que la copie et n'est propre et meme l'ecriture de 1/3 de premier page elle se recopie dans le 2 1/3 je veut le code sav pour pouvoir acceder au contraste

irelove · Answer

Bonjour mes chers collègues,
Veuillez bien me donner la liste des codes d'erreurs et solutions possiles sur canon IR toutes séries en français.
Merci portez-vous bien et à bientôt.

omar · Answer

very very very..............................thanks  Ploqui

Check all doors are fully shut including the lower left door.
Go into service mode by pressing * then #.
· Use left and right keys and find “printer”.
· find “reset printer”.
· Confirm yes to “reset printer”
· switch OFF for 5 seconds and ON again

karlmweru2020 · Answer

Salut pour le code e000 tu vas en sav et tu clich sur printer et dans printer tu fais reset printer. et ca Boum

MAODESI · Answer

moi, aussi le meme problème, aidez nous quand meme chers colleges

karlmweru2020 · Answer

E000 veut te dire que ton four a un probleme mais la plupart des cas, ce code apparait apres un mouvement brusque de tension. Ce qui veut dire que dans le cas probleme de tension, tu vas en sav et tu clitch sur printer et enfin sur reset. E007 est un probleme lié a la fixation. Quel autre me faut il te decrire?

karlmweru2020 · Answer

E000 veut te dire que ton four a un probleme mais la plupart des cas, ce code apparait apres un mouvement brusque de tension. Ce qui veut dire que dans le cas probleme de tension, tu vas en sav et tu clitch sur printer et enfin sur reset. E007 est un probleme lié a la fixation. Quel autre me faut il te decrire?

pathi · Answer

comment j'ai peut décode ma photocopieuse canon ir1600 s'affiche erreur système e 000

karlmweru2020 · Answer

Bien sur que oui.

Erreur systeme e000 canon ir 1600

29 réponses

Discussions similaires