View original (French)

HP IPAQ rz1710: How to turn it on?

Solved
pat25000 Posted messages 2 Status Member -  
 xavalou -
Hello,

I have a problem. I just acquired a PDA: it's an HP IPAQ rz1710, but I can't turn it on. With the stylus, I press RESET (on the bottom left), and then the screen lights up: at the top it says: "hp iPAQ Pocket PC" (on a blue background), in the middle of the screen there is a loading bar, and at the bottom, there is the HP invent logo, and finally, at the bottom right, in red, it says: "1.00.06 FRA".
When the loading bar is done, nothing happens. Additionally, when I plug it into the PC, nothing appears... I don't have an installation CD.
What should I do??? Please help me.
Thank you.
Configuration: Windows XP Internet Explorer 6.0

15 answers

  1. piothre
     
    I had the same problem, and by doing a hard reset, it finally turned back on. However, all the entered data was lost (not too serious if you sync regularly with your PC).
    On mine, to do the hard reset, I had to press two buttons + with a stylus on the usual reset button.

    Good luck!
    7
  2. pat25000 Posted messages 2 Status Member 1
     
    Thank you for the first response, but it doesn't help me at all... I bought it on eBay... Please help me.
    1
  3. xavalou
     
    Hello
    I just bought a HP iPAQ Pocket PC rz1710 and it is in Spanish
    I wanted to know the procedure to change it to French
    Thank you for your help
    And by the way, could you tell me if this PDA is good?
    1
  4. Ohm-WorK Posted messages 1468 Status Contributor 420
     
    Hi!

    In my opinion, go back to your dealer ;-)

    Bye
    --
    Life is a terminal illness, sexually transmitted (Woody Allen)
    0
  7. chevrolet
     
    Hello

    I have a problem with the memory extension card of my PC; I can't get the 1GB SD card to be recognized
    Is there any way to declare or format it???

    Thank you
    0
  8. JCC
     
    Hello,
    Have you tried leaving it on charge for a 'good' while?
    Then, keep the stylus pressed until the HP screen lights up, and then let the Windows bar charge normally

    It happens to me sometimes when the battery is empty.
    0
  9. pat_25
     
    Hello,
    Thank you very much for your response, but this question is 6 months old! I just bought this PDA. In fact, it just needed to be reset... Thank you for your information (for when the battery is empty) that is helpful because it often happens that I let it run out completely since I use my PDA a lot in MP3 mode (among other things).
    Are you satisfied with the battery life?
    Thank you!
    0
  10. JCC
     
    Hello, pat_25,

    Autonomy: N O T and besides, I often find this technology concentrate too hot.
    Well, it must be done, concentrating all that into just this,

    All the forums talk about a 1,800 battery, but the price!!! Well, excessive for me, so I leave it charging as much as possible, I am well equipped with all charging supports (car, usb, ...) and on top of that, with beautiful background slides, it's nice

    That's it
    0
  11. Flobo44
     
    Hello, I have a Compaq Ipaq 3600 that I can't turn on :s When I charged it for the first time, I heard a beep, then "Compaq" appeared on the screen, and then it disappeared, leaving red lines on the screen! :s And it's impossible to turn it back on... However, the PDA charges because the yellow light is flashing. How can I turn it back on???
    Thanks in advance! =D
    0
  12. marno
     
    Avec ce PDA HP IPAQ rz1710, il est possible de lire des vidéos, mais cela dépend du format des fichiers vidéo et des logiciels installés sur le dispositif. Voici comment procéder :

    1. **Vérifiez le format vidéo :** Assurez-vous que la vidéo est dans un format compatible avec le PDA, comme AVI ou WMV.

    2. **Installez un lecteur multimédia :** Si le lecteur par défaut ne prend pas en charge le format vidéo, téléchargez un lecteur multimédia compatible à partir d'une source fiable. Des options comme "TCPMP" ou "CorePlayer" sont souvent utilisées sur les appareils Windows Mobile.

    3. **Transférez la vidéo sur l'appareil :** Connectez le PDA à votre ordinateur et transférez le fichier vidéo sur le périphérique via USB ou carte mémoire.

    4. **Ouvrez le lecteur multimédia :** Lancez le lecteur vidéo installé et naviguez jusqu'au fichier vidéo que vous souhaitez lire.

    5. **Lancez la vidéo :** Sélectionnez le fichier et commencez la lecture.

    Assurez-vous que l’appareil est suffisamment chargé et que vous avez ajusté les réglages audio si nécessaire.
    0
    1. kyzer93380
       
      Yes, it's possible; you need to convert the videos to WMV with a conversion software, of course.
      0
  13. MADGREG
     
    Yes, indeed, the hard reset is the best solution. The issue on my part generally appeared after a long period of activity and a dead battery. To avoid this, it is better to charge it for a few minutes before turning it on.
    0
  14. MACGYVER
     
    Bonjour, j'ai acheté une iPad et le problème est qu'il s'allume mais la fenêtre HP ne s'allume pas, la barre en bas ne progresse pas. J'ai tenté une réinitialisation mais ça ne me donne rien. Si vous avez la solution, merci de me la donner. Merci.
    0
  15. 123ekramh
     
    Salut, il faut que tu appuies sur reset et en même temps sur on/off et c'est bon.
    0
  16. tof39 Posted messages 1 Status Member
     
    Hello
    to watch a divx, no problem, download the tcpmp-core software, free for pda
    but you need to take the pocketdvixencoder 3.60 program to encode them to pda format
    with this, very good picture and very good sound. After encoding, put them on your sd card, the film format is
    between 170 mb and 240 mb so a 256mb sd card is sufficient and it works.
    0