View original (French)

DEBUG ON ORION TV SCREEN

patchel -  
 Chine972 -
Hello, I am a regular user of your forum and have already found many solutions to various problems, and I commend the users who take the time to respond with great clarity. But today I have a problem and haven't found an answer.
-----------
So on a new ORION LCD television, the message "debug" has appeared on the screen only in TNT mode, and I can't seem to get rid of it, nor have I found any explanations in the manual or in a forum. Apparently, I am not the only one!
-----------
Thank you in advance for your responses.

9 answers

  1.
    Bidounet Posted messages 3 Registration date   Status Member Last intervention  
     
    Hello,

    Welcome to the club. And on top of that, it doesn't want to turn on anymore...
    0
    1. gitaneharibo
       
      My problem is exactly the same. To turn it on, I unplug the power cord and plug it back in immediately, and it works again.
      However, the "DEBUG" stays on!
      0
  2. gitaneharibo
     
    Hello, it's the same for me, I join you: I have the same message and the TV refuses to turn on! I can only get it to work if I unplug it and then plug it back in.
    0
  3. icar370 Posted messages 1 Registration date   Status Member Last intervention  
     
    Hello, I'm in the same situation as you except that mine is still working.
    0
  4. gitaneharibo
     
    Hello,
    Finished displaying "DEBUG"

    Please follow the instructions contained below precisely (TV buttons and TLC buttons).
    Everything should normally be back to normal.

    1 / Turn the volume down to the minimum (Vol -)

    2 / Press "Vol - of the TV" and "button 6 of the TLC" simultaneously and hold for about 5 seconds.

    3 / Press 0321 on the TLC in succession.

    4 / Press the "Up arrow" on the TLC until 0D24 appears on the screen.

    5 / Press the "Right arrow" on the TLC. The screen displays 0D24 - 00 (00 blinks).

    6 / Type 01 on the TLC - The screen displays 0D24 - 01 (01 blinks).

    7 / Press the "Left arrow" to return to 0D24.

    8 / Put the TV in standby to save.

    END
    0
    1. Guépard
       
      Hello, gitaneharibo

      You seem to be well acquainted with ORION TVs.

      Here's my problem: on an LCD model no. TV32RN10D, purchased at my local Intermarché.

      I can't seem to "enter" the "EPG Timer" menu.
      I'm following the instructions in the manual:
      1/ Press the "Guide" button
      2/ Select the desired channel using the navigation arrows
      3/ Confirm by pressing "enter"
      4/ Press the guide button twice.

      And then, the issue arises; the menu doesn't appear as stated, I either open or close the guide menu, as if the double press is not being detected and distinguished from the single press.

      What should I do?

      I've checked the notice in English, in case of poor translation, but the instructions are the same...

      Last question, the address info@exlalto.be no longer works, is there a support service for the brand?

      Thanks in advance for the reply.
      0
      1. gitaneharibo > Guépard
         
        Remarks.

        If you select an event that has already started, the selected program will be displayed on the screen and you cannot set the timer for a program that has already started.
        To display the saved timer events, press GUIDE twice. The EPG Timer menu will appear (Press the ‘red’ button to set the Timer mode for a specific event. You can also delete or change the frequency (Once / Daily / Weekly) of the saved timer events (but note that you cannot view the scheduled times set from the EPG).
        0
  6. patchel
     
    Thank you, I will try the operation tomorrow evening, I am traveling and will keep you updated. See you later.
    0
  7. patchel
     
    Hello, great it works, thank you very much.
    0
  8. Bidounet Posted messages 3 Registration date   Status Member Last intervention  
     
    Here it is working. Thank you very much. Do you sometimes have the number "888" that appears at the top??? You just need to change the channel for it to go away!!!
    0
  9. diversion
     
    Hello everyone,

    great, the procedure works well but three days later the debug display reappears and I have to start all over again,

    are you experiencing the same problem?
    0
    1. gitaneharibo
       
      No, I don't have a problem. Since the tweak... the 'DEBUG' hasn't come back, fortunately, and I haven't had any other issues with this TV.
      0
  10. Chine972
     

    Hello, I'm encountering the same issue as you, but I have a Telefunken TV... how do I perform the operation to remove the "debug player" message?

    0