[Fedora 13] Pas d'internet ni en Eth ni Wifi

Arno59 Messages postés 4753 Statut Contributeur -  
nimoinau Messages postés 95 Statut Membre -
Bonjour,


Je viens d'installer Linux Fedora 13 sur le Pc portable HP 6735s, tout s'est correctement installé, mais je n'ai pas de réseau ?

Site constructeur HP :
http://h20000.www2.hp.com/bizsupport/TechSupport/Home.jsp?lang=fr&cc=fr&prodTypeId=321957&prodSeriesId=3687621&submit.y=0&submit.x=0&lang=fr&cc=fr

--> Le voyant du témoin du wi-fi sur le clavier est allumé orange:


--> pour plus d'information :

--> Mode Graphique :
--> Système -> Administration -> Réseau --> Configuration Réseau

--> Périphérique :
Désactivé : eth0 : type ethernet
Désactivé : wlan0 : Wireless

Pour le port Eth0 : Marvell Technology Group Ltd Unknown (0x4357)
Pour le wi-fi : Broadcom Corporation BCM4312 802.11b/g LP-PHY

Commande
dmidecode 

# dmidecode 2.9
SMBIOS 2.4 present.
19 structures occupying 1003 bytes.
Table at 0xAFDBC000.

Handle 0x0009, DMI type 0, 24 bytes
BIOS Information
    Vendor: Hewlett-Packard
    Version: 68GPP Ver. F.09
    Release Date: 03/05/2009
    Address: 0xF0000
    Runtime Size: 64 kB
    ROM Size: 2048 kB
    Characteristics:
        PCI is supported
        PC Card (PCMCIA) is supported
        BIOS is upgradeable
        BIOS shadowing is allowed
        Boot from CD is supported
        Selectable boot is supported
        EDD is supported
        Print screen service is supported (int 5h)
        8042 keyboard services are supported (int 9h)
        Serial services are supported (int 14h)
        Printer services are supported (int 17h)
        ACPI is supported
        USB legacy is supported
        Smart battery is supported
        BIOS boot specification is supported
        Function key-initiated network boot is supported
        Targeted content distribution is supported
    BIOS Revision: 15.9
    Firmware Revision: 94.31

Handle 0x000A, DMI type 1, 27 bytes
System Information
    Manufacturer: Hewlett-Packard
    Product Name: HP Compaq 6735s
    Version: F.09
    Serial Number: C******
    UUID: 3******-8417-DE11-8***-2AD******
    Wake-up Type: Power Switch
    SKU Number: G****AV
    Family: 103C_5336AN

Handle 0x000B, DMI type 2, 16 bytes
Base Board Information
    Manufacturer: Hewlett-Packard
    Product Name: 30E4
    Version: KBC Version 94.1E
    Serial Number: Base Board Serial Number
    Asset Tag: Base Board Asset Tag
    Features:
        Board is a hosting board
        Board is replaceable
    Location In Chassis: Base Board Chassis Location
    Chassis Handle: 0x000C
    Type: Unknown
    Contained Object Handles: 0

Handle 0x000C, DMI type 3, 17 bytes
Chassis Information
    Manufacturer: Hewlett-Packard
    Type: Notebook
    Lock: Not Present
    Version: Not Specified
    Serial Number: CNU9154DG4
    Asset Tag: CNU9154DG4
    Boot-up State: Safe
    Power Supply State: Safe
    Thermal State: Other
    Security Status: Other
    OEM Information: 0x00000000

Handle 0x0000, DMI type 4, 35 bytes
Processor Information
    Socket Designation: Unknown
    Type: Central Processor
    Family: <OUT OF SPEC>
    Manufacturer: AMD Corporation
    ID: 31 0F 20 00 FF FB 8B 17
    Version: AMD Turion(tm)X2 Dual Core Mobile RM-72
    Voltage: 1.5 V
    External Clock: 200 MHz
    Max Speed: 2100 MHz
    Current Speed: 2100 MHz
    Status: Populated, Enabled
    Upgrade: <OUT OF SPEC>
    L1 Cache Handle: 0x0001
    L2 Cache Handle: 0x0002
    L3 Cache Handle: Not Provided
    Serial Number: NotSupport
    Asset Tag: FFFF
    Part Number: Not Specified

Handle 0x0001, DMI type 7, 19 bytes
Cache Information
    Socket Designation: L1 Cache
    Configuration: Enabled, Not Socketed, Level 1
    Operational Mode: Write Back
    Location: Internal
    Installed Size: 256 KB
    Maximum Size: 256 KB
    Supported SRAM Types:
        Pipeline Burst
    Installed SRAM Type: Pipeline Burst
    Speed: Unknown
    Error Correction Type: Multi-bit ECC
    System Type: Unified
    Associativity: 2-way Set-associative

Handle 0x0002, DMI type 7, 19 bytes
Cache Information
    Socket Designation: L2 Cache
    Configuration: Enabled, Not Socketed, Level 2
    Operational Mode: Write Back
    Location: Internal
    Installed Size: 1024 KB
    Maximum Size: 1024 KB
    Supported SRAM Types:
        Pipeline Burst
    Installed SRAM Type: Pipeline Burst
    Speed: Unknown
    Error Correction Type: Multi-bit ECC
    System Type: Unified
    Associativity: 16-way Set-associative

Handle 0x0010, DMI type 9, 13 bytes
System Slot Information
    Designation: PCI SLOT1
    Type: 32-bit PCI
    Current Usage: Available
    Length: Long
    ID: 1
    Characteristics:
        3.3 V is provided
        PME signal is supported
        SMBus signal is supported

Handle 0x000E, DMI type 10, 6 bytes
On Board Device Information
    Type: Video
    Status: Enabled
    Description: 256

Handle 0x000F, DMI type 11, 5 bytes
OEM Strings
    String 1: ABS 70/71 79 7A 7B 7C
    String 2: CSM v02.2A
    String 3: www.hp.com

Handle 0x0003, DMI type 16, 15 bytes
Physical Memory Array
    Location: System Board Or Motherboard
    Use: System Memory
    Error Correction Type: None
    Maximum Capacity: 3 GB
    Error Information Handle: Not Provided
    Number Of Devices: 2

Handle 0x0004, DMI type 17, 27 bytes
Memory Device
    Array Handle: 0x0003
    Error Information Handle: Not Provided
    Total Width: 64 bits
    Data Width: 64 bits
    Size: 1024 MB
    Form Factor: SODIMM
    Set: None
    Locator: SODIMM 0
    Bank Locator: BANK0
    Type: DDR2
    Type Detail: Synchronous
    Speed: 800 MHz (1.2 ns)
    Manufacturer: Samsung
    Serial Number: CE00000000000000020914956D0A58
    Asset Tag: Unknown
    Part Number: M4 70T2864QZ3-CF7 

Handle 0x0006, DMI type 17, 27 bytes
Memory Device
    Array Handle: 0x0003
    Error Information Handle: Not Provided
    Total Width: 64 bits
    Data Width: 64 bits
    Size: 2048 MB
    Form Factor: SODIMM
    Set: None
    Locator: SODIMM 1
    Bank Locator: BANK0
    Type: DDR2
    Type Detail: Synchronous
    Speed: 800 MHz (1.2 ns)
    Manufacturer: Unknown
    Serial Number: AD0000000000000001091000005201
    Asset Tag: Unknown
    Part Number: HYMP125S64CP8-S6  

Handle 0x0008, DMI type 19, 15 bytes
Memory Array Mapped Address
    Starting Address: 0x00000000000
    Ending Address: 0x000BFFFFFFF
    Range Size: 3 GB
    Physical Array Handle: 0x0003
    Partition Width: 0

Handle 0x0005, DMI type 20, 19 bytes
Memory Device Mapped Address
    Starting Address: 0x00000000000
    Ending Address: 0x0003FFFFFFF
    Range Size: 1 GB
    Physical Device Handle: 0x0004
    Memory Array Mapped Address Handle: 0x0008
    Partition Row Position: 1

Handle 0x0007, DMI type 20, 19 bytes
Memory Device Mapped Address
    Starting Address: 0x00040000000
    Ending Address: 0x000BFFFFFFF
    Range Size: 2 GB
    Physical Device Handle: 0x0006
    Memory Array Mapped Address Handle: 0x0008
    Partition Row Position: 1

Handle 0x0011, DMI type 22, 26 bytes
Portable Battery
    Location: Primary
    Manufacturer: STL-SOG6F
    Manufacture Date: 3A81
    Serial Number: 0328
    Name: DD06047
    Design Capacity: 4400 mWh
    Design Voltage: 10800 mV
    SBDS Version: 1.1
    Maximum Error: Unknown
    SBDS Chemistry: LION
    OEM-specific Information: 0x00000000

Handle 0x000D, DMI type 32, 20 bytes
System Boot Information
    Status: No errors detected

Handle 0xFFFD, DMI type 127, 4 bytes
End Of Table


Que dois-je contrôler et tester pour mettre le wifi le cable ethernet ?
A voir également:

8 réponses

Réponse 1 / 8
HostOfSeraphim Messages postés 7340 Statut Contributeur 1 608
 
Que répond ifconfig ?

0
Réponse 2 / 8
Arno59 Messages postés 4753 Statut Contributeur 487
 
ifconfig -a
Code:

eth0 Link encap:Ethernet HWaddr 00:**:**:**:**:**
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interruption:16

lo Link encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
adr inet6: ::1/128 Scope:Hôte
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
RX bytes:480 (480.0 b) TX bytes:480 (480.0 b)
0
Réponse 3 / 8
nimoinau Messages postés 95 Statut Membre 5
 
salut,
en regardant dans la doc ubuntu, le 6735 a parfois des problèmes de connexion (comme le 6720).
un début de réponse dans ce forum :
http://ubuntuforums.org/showthread.php?t=659027
0
Réponse 4 / 8
Arno59 Messages postés 4753 Statut Contributeur 487
 
Merci pour le de début de réponse.

Est-ce valable pour Fedora 13 & Ubuntu 10.04 ?

--> ndiswrapper sous Linux Fedora ?

Pilote pour Windows XP :
ftp://ftp.compaq.com/pub/softpaq/sp34001-34500/sp34152.exe

Version du Kernel sous Linux Fedora 13 : 2.6.33.3-85.fc13.i686.PAE


L'Open source répond à la liberté de choix du consommateur du XXIe siècle
0

Vous n’avez pas trouvé la réponse que vous recherchez ?

Posez votre question
Réponse 5 / 8
nimoinau Messages postés 95 Statut Membre 5
 
pour le cable ethernet je pense que oui. sauf que tu as grub-pc et non plus grub-legacy donc il faut aller modifier /boot/grub/grub.cfg

pour le wifi y'a pas de raison.
0
Arno59 Messages postés 4753 Statut Contributeur 487
 
Merci mais le fichier que tu me dit n'existe pas sous LInux Fedora 13.

Voici ce que j'ai de mon coté : 
 cd /boot/grub/
[root@localhost grub]# ls
device.map     grub.conf         minix_stage1_5     stage2
e2fs_stage1_5  iso9660_stage1_5  reiserfs_stage1_5  ufs2_stage1_5
fat_stage1_5   jfs_stage1_5      splash.xpm.gz      vstafs_stage1_5
ffs_stage1_5   menu.lst          stage1             xfs_stage1_5


[root@localhost grub]# cat /boot/grub/grub.conf
# grub.conf generated by anaconda
#
# Note that you do not have to rerun grub after making changes to this file
# NOTICE:  You have a /boot partition.  This means that
#          all kernel and initrd paths are relative to /boot/, eg.
#          root (hd0,0)
#          kernel /vmlinuz-version ro root=/dev/mapper/VolGroup-lv_root
#          initrd /initrd-[generic-]version.img
#boot=/dev/sda
default=0
timeout=5
splashimage=(hd0,0)/grub/splash.xpm.gz
hiddenmenu
title Fedora (2.6.33.3-85.fc13.i686.PAE)
	root (hd0,0)
	kernel /vmlinuz-2.6.33.3-85.fc13.i686.PAE ro root=/dev/mapper/VolGroup-lv_root rd_LVM_LV=VolGroup/lv_root rd_LVM_LV=VolGroup/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=fr_FR.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=fr rhgb quiet
	initrd /initramfs-2.6.33.3-85.fc13.i686.PAE.img
title Other
	rootnoverify (hd0,2)
	chainloader +1
0
nimoinau Messages postés 95 Statut Membre 5
 
affiche le contenu de ton menu.lst
0
Arno59 Messages postés 4753 Statut Contributeur 487
 
Bonsoir

Le contenu du fichier menu.lst est identique à grub.conf


cat /boot/grub/menu.lst 

# grub.conf generated by anaconda
#
# Note that you do not have to rerun grub after making changes to this file
# NOTICE:  You have a /boot partition.  This means that
#          all kernel and initrd paths are relative to /boot/, eg.
#          root (hd0,0)
#          kernel /vmlinuz-version ro root=/dev/mapper/VolGroup-lv_root
#          initrd /initrd-[generic-]version.img
#boot=/dev/sda
default=0
timeout=5
splashimage=(hd0,0)/grub/splash.xpm.gz
hiddenmenu
title Fedora (2.6.33.3-85.fc13.i686.PAE)
	root (hd0,0)
	kernel /vmlinuz-2.6.33.3-85.fc13.i686.PAE ro root=/dev/mapper/VolGroup-lv_root rd_LVM_LV=VolGroup/lv_root rd_LVM_LV=VolGroup/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=fr_FR.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=fr rhgb quiet
	initrd /initramfs-2.6.33.3-85.fc13.i686.PAE.img
title Other
	rootnoverify (hd0,2)
	chainloader +1
0
Réponse 6 / 8
Arno59 Messages postés 4753 Statut Contributeur 487
 
Merci à tous pour vos réponse,

Je n'ai toujours pas d'internet depuis le Wifi ni eternet.

Que dois-je faire ?
0
Réponse 7 / 8
nimoinau Messages postés 95 Statut Membre 5
 
qu'as tu fait ?
est-ce que tu as essayé les manips du lien ?
0
Réponse 8 / 8
nimoinau Messages postés 95 Statut Membre 5
 
tu peux essayer de modifier ton menu.lst comme indiqué dans le lien.

d'abord tu sauvegarde ton fichier menu.lst

puis après

kernel /vmlinuz-2.6.33.3-85.fc13.i686.PAE ro

tu rajoutes pci=noacpi

essayes ce que ca donne.

ou sinon y'a ça :

Hard Way : To solve once for all the ethernet trouble under ubuntu you have to upgrade the firmware of your ethernet device (or the bios of your motherboard), but you need windows to do this operation (however if you search in the ubuntu forums you'll find a way to do this operation under ubuntu too)
0

Discussions similaires

Voxbone ? qui est-ce ?
fanfan54 -
ntrece13 -

159 réponses
Comment faire pour débloquer un problème de connexion IPTV ?
Micka -
bidule... -

13 réponses
Adaptateur USB pour le WIFI 7 ...
toinou90 -
brupala -

14 réponses