Cisco 1841 ne boot pas correctement

Bonjour,

j'ai un Routeur Cisco 1800 serie (1841) que je voudrais m'exercer dessus mais lors du demarrage je me trouve bolcker avec le message suivant :

System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)
Technical Support: https://www.cisco.com/c/en/us/support/index.html
Copyright (c) 2004 by cisco Systems, Inc.
PLD version 0x10
GIO ASIC version 0x127 c1841 processor with 131072 Kbytes of main memory
Main memory is configured to 64 bit mode with parity disabled


Readonly ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xc100

Initializing ATA monitor library.......
program load complete, entry point: 0x8000f000, size: 0xc100

Initializing ATA monitor library.......

program load complete, entry point: 0x8000f000, size: 0xd4a9a0
Self decompressing the image : #################################################
################################################################################
######## [OK]

Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
0X003AA110 public buffer pools
0X00211000 public particle pools
0X000021B8 Onboard USB

If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.

Allocating additional 7713952 bytes to IO Memory.
PMem allocated: 117440512 bytes; IOMem allocated: 16777216 bytes

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706



Cisco IOS Software, 1841 Software (C1841-IPBASE-M), Version 12.4(1c), RELEASE SO
FTWARE (fc1)
Technical Support: https://www.cisco.com/c/en/us/support/index.html
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Tue 25-Oct-05 17:10 by evmiller
Image text-base: 0x6007ECA0, data-base: 0x61480000

Port Statistics for unclassified packets is not turned on.
Cisco 1841 (revision 6.0) with 114688K/16384K bytes of memory.
Processor board ID FCZ101822GD
2 FastEthernet interfaces
DRAM configuration is 64 bits wide with parity disabled.
191K bytes of NVRAM.
31360K bytes of ATA CompactFlash (Read/Write)



Press RETURN to get started!


*Aug 5 08:05:34.271: %LINEPROTO-5-UPDOWN: Line protocol on Interface NVI0, chan
ged state to up
*Aug 5 08:05:34.831: %SYS-5-CONFIG_I: Configured from memory by console
*Aug 5 08:05:35.215: %SYS-5-RESTART: System restarted --
Cisco IOS Software, 1841 Software (C1841-IPBASE-M), Version 12.4(1c), RELEASE SO
FTWARE (fc1)
Technical Support: https://www.cisco.com/c/en/us/support/index.html
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Tue 25-Oct-05 17:10 by evmiller
*Aug 5 08:05:35.219: %SNMP-5-COLDSTART: SNMP agent on host MSFB_local is underg
oing a cold start
*Aug 5 08:05:37.271: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state t
o up
*Aug 5 08:05:40.271: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state t
o up
*Aug 5 08:05:43.271: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
et0/0, changed state to up
*Aug 5 08:05:43.271: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
et0/1, changed state to down
*Aug 5 08:05:46.271: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
et0/0, changed state to down

et a cet niveau je ne peu plus rien faire. si quelqu'un pourrait m'aider a avoir une solution me fera très plaisir.

thanks !