Ubuntu rechercher windows help!

Bonjour,
VOILA jsuis en pleine deprime je vous explique , il ya quelques jours mon ordi xp ne demarrait plus il me disait qu'il y avait un probleme et me proposait de demarrer en mode sans echec...
bref souci avec mon disque dur, trop plein je crois! donc au lieu de reformater car je voulais sauver des donnees du disque dur et en plus je n'ai pu cd d'installation xp et drivers! je sais c tres con!!
donc je me suis renseigne sur internet et j'ai vu qu'on pouvait demarrer le systeme avec un live cd , j'ai pris ubuntu d'apres les forums, j'ai bien galere a l'installer j'ai du partitionner mon disque dur notamment! une fois lance ubuntu reconnait bieninternet, les ports usb etc... DONC TRES BIEN!
Malheureusement j'ai suivi toutes les instructions que j'ai pu trouver sur le net pour retrouver mes partitions du disque dur et sauver mes donnees mais impossible voici un ptit echantillon des recherches effectuees!

[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1494.382 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.004000] allocated 3276720 bytes of page_cgroup
[ 0.004000] please try cgroup_disable=memory option if you don't want
[ 0.004000] Scanning for low memory corruption every 60 seconds
[ 0.004000] Memory: 630376k/655344k available (4126k kernel code, 24252k reserved, 2208k data, 532k init, 0k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xffc77000 - 0xfffff000 (3616 kB)
[ 0.004000] pkmap : 0xff400000 - 0xff800000 (4096 kB)
[ 0.004000] vmalloc : 0xe87fc000 - 0xff3fe000 ( 364 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xe7ffc000 ( 639 MB)
[ 0.004000] .init : 0xc0737000 - 0xc07bc000 ( 532 kB)
[ 0.004000] .data : 0xc0507a6f - 0xc072fe60 (2208 kB)
[ 0.004000] .text : 0xc0100000 - 0xc0507a6f (4126 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.004000] SLUB: Genslabs=12, HWalign=128, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.004021] Calibrating delay loop (skipped), value calculated using timer frequency.. 2988.76 BogoMIPS (lpj=5977528)
[ 0.004062] Security Framework initialized
[ 0.004079] SELinux: Disabled at boot.
[ 0.004118] AppArmor: AppArmor initialized
[ 0.004143] Mount-cache hash table entries: 512
[ 0.004457] Initializing cgroup subsys ns
[ 0.004468] Initializing cgroup subsys cpuacct
[ 0.004476] Initializing cgroup subsys memory
[ 0.004487] Initializing cgroup subsys freezer
[ 0.004523] CPU: Trace cache: 12K uops, L1 D cache: 8K
[ 0.004533] CPU: L2 cache: 256K
[ 0.004541] CPU: Hyper-Threading is disabled
[ 0.004578] Checking 'hlt' instruction... OK.
[ 0.021357] SMP alternatives: switching to UP code
[ 0.221053] Freeing SMP alternatives: 18k freed
[ 0.221065] ACPI: Core revision 20080926
[ 0.223175] ACPI: Checking initramfs for custom DSDT
[ 0.813276] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.853001] CPU0: Intel(R) Pentium(R) 4 CPU 1.50GHz stepping 02
[ 0.856002] Brought up 1 CPUs
[ 0.856002] Total of 1 processors activated (2988.76 BogoMIPS).
[ 0.856002] CPU0 attaching NULL sched-domain.
[ 0.856002] net_namespace: 776 bytes
[ 0.856002] Booting paravirtualized kernel on bare hardware
[ 0.856002] Time: 9:26:45 Date: 05/08/09
[ 0.856002] regulator: core version 0.5
[ 0.856002] NET: Registered protocol family 16
[ 0.856002] EISA bus registered
[ 0.856002] ACPI: bus type pci registered
[ 0.857200] PCI: PCI BIOS revision 2.10 entry at 0xf1060, last bus=2
[ 0.857205] PCI: Using configuration type 1 for base access
[ 0.860400] ACPI: EC: Look up EC in DSDT
[ 0.868880] ACPI: Interpreter enabled
[ 0.868894] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.868943] ACPI: Using IOAPIC for interrupt routing
[ 0.889384] ACPI: No dock devices found.
[ 0.889410] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.889507] pci 0000:00:00.0: reg 10 32bit mmio: [0xf8000000-0xfbffffff]
[ 0.889730] pci 0000:00:1f.0: Enabled i801 SMBus device
[ 0.889742] pci 0000:00:1f.0: quirk: region e400-e47f claimed by ICH4 ACPI/GPIO/TCO
[ 0.889748] pci 0000:00:1f.0: quirk: region ec00-ec3f claimed by ICH4 GPIO
[ 0.889804] pci 0000:00:1f.1: reg 20 io port: [0xb800-0xb80f]
[ 0.889878] pci 0000:00:1f.2: reg 20 io port: [0xb400-0xb41f]
[ 0.889948] pci 0000:00:1f.3: reg 20 io port: [0xe800-0xe80f]
[ 0.890024] pci 0000:00:1f.4: reg 20 io port: [0xb000-0xb01f]
[ 0.890070] pci 0000:00:1f.5: reg 10 io port: [0xa800-0xa8ff]
[ 0.890081] pci 0000:00:1f.5: reg 14 io port: [0xa400-0xa43f]
[ 0.890173] pci 0000:01:00.0: reg 10 32bit mmio: [0xee000000-0xeeffffff]
[ 0.890184] pci 0000:01:00.0: reg 14 32bit mmio: [0xf0000000-0xf7ffffff]
[ 0.890213] pci 0000:01:00.0: reg 30 32bit mmio: [0xefff0000-0xefffffff]
[ 0.890280] pci 0000:00:01.0: bridge 32bit mmio: [0xee000000-0xefefffff]
[ 0.890287] pci 0000:00:01.0: bridge 32bit mmio pref: [0xeff00000-0xf7ffffff]
[ 0.890348] pci 0000:02:08.0: reg 10 32bit mmio: [0xed800000-0xed800fff]
[ 0.890359] pci 0000:02:08.0: reg 14 io port: [0xd800-0xd83f]
[ 0.890402] pci 0000:02:08.0: supports D1 D2
[ 0.890407] pci 0000:02:08.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.890414] pci 0000:02:08.0: PME# disabled
[ 0.890458] pci 0000:02:09.0: reg 10 32bit mmio: [0xed000000-0xed000fff]
[ 0.890507] pci 0000:02:09.0: supports D1 D2
[ 0.890511] pci 0000:02:09.0: PME# supported from D0 D1 D2 D3hot
[ 0.890518] pci 0000:02:09.0: PME# disabled
[ 0.890563] pci 0000:02:09.1: reg 10 32bit mmio: [0xec800000-0xec800fff]
[ 0.890611] pci 0000:02:09.1: supports D1 D2
[ 0.890615] pci 0000:02:09.1: PME# supported from D0 D1 D2 D3hot
[ 0.890622] pci 0000:02:09.1: PME# disabled
[ 0.890669] pci 0000:02:09.2: reg 10 32bit mmio: [0xec000000-0xec0000ff]
[ 0.890718] pci 0000:02:09.2: supports D1 D2
[ 0.890723] pci 0000:02:09.2: PME# supported from D0 D1 D2 D3hot
[ 0.890730] pci 0000:02:09.2: PME# disabled
[ 0.890785] pci 0000:02:0a.0: reg 10 32bit mmio: [0xeb800000-0xeb8007ff]
[ 0.890797] pci 0000:02:0a.0: reg 14 32bit mmio: [0xeb000000-0xeb003fff]
[ 0.890843] pci 0000:02:0a.0: supports D2
[ 0.890847] pci 0000:02:0a.0: PME# supported from D2 D3hot
[ 0.890854] pci 0000:02:0a.0: PME# disabled
[ 0.890899] pci 0000:02:0b.0: reg 10 io port: [0xd400-0xd43f]
[ 0.890950] pci 0000:02:0b.0: supports D2
[ 0.890954] pci 0000:02:0b.0: PME# supported from D0 D2 D3hot D3cold
[ 0.890961] pci 0000:02:0b.0: PME# disabled
[ 0.891002] pci 0000:00:1e.0: transparent bridge
[ 0.891010] pci 0000:00:1e.0: bridge io port: [0xd000-0xdfff]
[ 0.891018] pci 0000:00:1e.0: bridge 32bit mmio: [0xeb000000-0xedffffff]
[ 0.891038] bus 00 -> node 0
[ 0.891052] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.891250] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
[ 0.891416] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI2._PRT]
[ 0.957003] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 0.957201] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.957395] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.957618] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[ 0.957808] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.958001] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.958194] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.958415] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[ 0.958686] ACPI: WMI: Mapper loaded
[ 0.959209] SCSI subsystem initialized
[ 0.959330] libata version 3.00 loaded.
[ 0.959456] usbcore: registered new interface driver usbfs
[ 0.959502] usbcore: registered new interface driver hub
[ 0.959574] usbcore: registered new device driver usb
[ 0.959873] PCI: Using ACPI for IRQ routing
[ 0.960109] Bluetooth: Core ver 2.13
[ 0.960156] NET: Registered protocol family 31
[ 0.960161] Bluetooth: HCI device and connection manager initialized
[ 0.960169] Bluetooth: HCI socket layer initialized
[ 0.960174] NET: Registered protocol family 8
[ 0.960178] NET: Registered protocol family 20
[ 0.960206] NetLabel: Initializing
[ 0.960210] NetLabel: domain hash size = 128
[ 0.960213] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.960244] NetLabel: unlabeled traffic allowed by default
[ 0.960435] AppArmor: AppArmor Filesystem Enabled
[ 0.960472] pnp: PnP ACPI init
[ 0.960472] ACPI: bus type pnp registered
[ 0.970327] pnp: PnP ACPI: found 17 devices
[ 0.970334] ACPI: ACPI bus type pnp unregistered
[ 0.970344] PnPBIOS: Disabled by ACPI PNP
[ 0.970369] system 00:00: iomem range 0x0-0x9ffff could not be reserved
[ 0.970376] system 00:00: iomem range 0xf0000-0xfffff could not be reserved
[ 0.970382] system 00:00: iomem range 0x100000-0x27ffffff could not be reserved
[ 0.970389] system 00:00: iomem range 0xfec00000-0xfec000ff has been reserved
[ 0.970395] system 00:00: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.970410] system 00:02: ioport range 0xe400-0xe47f has been reserved
[ 0.970416] system 00:02: ioport range 0xe800-0xe81f could not be reserved
[ 0.970422] system 00:02: ioport range 0xec00-0xec3f has been reserved
[ 0.970427] system 00:02: ioport range 0x4d6-0x4d6 has been reserved
[ 0.970433] system 00:02: iomem range 0xfff80000-0xffffffff could not be reserved
[ 0.970439] system 00:02: iomem range 0xffb80000-0xffbfffff has been reserved
[ 0.970452] system 00:03: ioport range 0x4d0-0x4d1 has been reserved
[ 0.970472] system 00:0e: ioport range 0xec80-0xec8f has been reserved
[ 0.970477] system 00:0e: ioport range 0xecc0-0xeccf has been reserved
[ 0.970483] system 00:0e: ioport range 0xecd0-0xecdf has been reserved
[ 0.970488] system 00:0e: ioport range 0xecf0-0xecff has been reserved
[ 1.005456] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 1.005461] pci 0000:00:01.0: IO window: disabled
[ 1.005470] pci 0000:00:01.0: MEM window: 0xee000000-0xefefffff
[ 1.005477] pci 0000:00:01.0: PREFETCH window: 0x000000eff00000-0x000000f7ffffff
[ 1.005488] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02
[ 1.005493] pci 0000:00:1e.0: IO window: 0xd000-0xdfff
[ 1.005502] pci 0000:00:1e.0: MEM window: 0xeb000000-0xedffffff
[ 1.005509] pci 0000:00:1e.0: PREFETCH window: disabled
[ 1.005538] pci 0000:00:1e.0: setting latency timer to 64
[ 1.005547] bus: 00 index 0 io port: [0x00-0xffff]
[ 1.005552] bus: 00 index 1 mmio: [0x000000-0xffffffff]
[ 1.005557] bus: 01 index 0 mmio: [0x0-0x0]
[ 1.005561] bus: 01 index 1 mmio: [0xee000000-0xefefffff]
[ 1.005566] bus: 01 index 2 mmio: [0xeff00000-0xf7ffffff]
[ 1.005569] bus: 01 index 3 mmio: [0x0-0x0]
[ 1.005574] bus: 02 index 0 io port: [0xd000-0xdfff]
[ 1.005578] bus: 02 index 1 mmio: [0xeb000000-0xedffffff]
[ 1.005582] bus: 02 index 2 mmio: [0x0-0x0]
[ 1.005586] bus: 02 index 3 io port: [0x00-0xffff]
[ 1.005590] bus: 02 index 4 mmio: [0x000000-0xffffffff]
[ 1.005615] NET: Registered protocol family 2
[ 1.005904] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 1.006705] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 1.009347] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 1.010744] TCP: Hash tables configured (established 131072 bind 65536)
[ 1.010754] TCP reno registered
[ 1.011144] NET: Registered protocol family 1
[ 1.011464] checking if image is initramfs...<7>Switched to high resolution mode on CPU 0
[ 1.880163] it is
[ 3.099266] Freeing initrd memory: 7357k freed
[ 3.099377] Simple Boot Flag at 0x3a set to 0x1
[ 3.099441] cpufreq: No nForce2 chipset.
[ 3.099814] audit: initializing netlink socket (disabled)
[ 3.099859] type=2000 audit(1241774807.096:1): initialized
[ 3.121013] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 3.126218] VFS: Disk quotas dquot_6.5.1
[ 3.126495] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 3.129397] fuse init (API version 7.10)
[ 3.129804] msgmni has been set to 1246
[ 3.130707] alg: No test for stdrng (krng)
[ 3.130776] io scheduler noop registered
[ 3.130784] io scheduler anticipatory registered
[ 3.130792] io scheduler deadline registered
[ 3.130921] io scheduler cfq registered (default)
[ 3.131102] pci 0000:01:00.0: Boot video device
[ 3.149075] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 3.149121] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 3.149638] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 3.149652] ACPI: Power Button (FF) [PWRF]
[ 3.149827] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 3.149838] ACPI: Power Button (CM) [PWRB]
[ 3.150422] processor ACPI_CPU:00: registered as cooling_device0
[ 3.177382] isapnp: Scanning for PnP cards...
[ 3.531686] isapnp: No Plug & Play device found
[ 3.536864] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 3.537105] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 3.537353] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 3.538542] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 3.538917] 00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 3.539378] serial 0000:02:0b.0: enabling device (0080 -> 0081)
[ 3.539430] serial 0000:02:0b.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 3.543874] brd: module loaded
[ 3.545392] loop: module loaded
[ 3.545829] Fixed MDIO Bus: probed
[ 3.545857] PPP generic driver version 2.4.2
[ 3.546120] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[ 3.546269] Driver 'sd' needs updating - please use bus_type methods
[ 3.546313] Driver 'sr' needs updating - please use bus_type methods
[ 3.546632] ata_piix 0000:00:1f.1: version 2.12
[ 3.546849] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 3.547282] scsi0 : ata_piix
[ 3.547791] scsi1 : ata_piix
[ 3.549650] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xb800 irq 14
[ 3.549664] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xb808 irq 15
[ 3.712603] ata1.00: ATA-6: Maxtor 4D060H3, DAH017K0, max UDMA/100
[ 3.712609] ata1.00: 120069936 sectors, multi 16: LBA
[ 3.712660] ata1.00: limited to UDMA/33 due to 40-wire cable
[ 3.728564] ata1.00: configured for UDMA/33
[ 3.916377] ata2.00: ATAPI: PIONEER DVD-ROM DVD-116 ATAPI Model 0121, E1.21, max UDMA/33
[ 3.916467] ata2.01: ATAPI: Hewlett-Packard CD-Writer cd16f, 1.1D, max UDMA/33
[ 3.932356] ata2.00: configured for UDMA/33
[ 3.964327] ata2.01: configured for UDMA/33
[ 3.965982] scsi 0:0:0:0: Direct-Access ATA Maxtor 4D060H3 DAH0 PQ: 0 ANSI: 5
[ 3.966250] sd 0:0:0:0: [sda] 120069936 512-byte hardware sectors: (61.4 GB/57.2 GiB)
[ 3.966289] sd 0:0:0:0: [sda] Write Protect is off
[ 3.966294] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.966349] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.966520] sd 0:0:0:0: [sda] 120069936 512-byte hardware sectors: (61.4 GB/57.2 GiB)
[ 3.966553] sd 0:0:0:0: [sda] Write Protect is off
[ 3.966559] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.966613] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.966623] sda: sda1 sda2 < sda5 sda6 sda7 sda8 >
[ 4.062740] sd 0:0:0:0: [sda] Attached SCSI disk
[ 4.062872] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 4.064300] scsi 1:0:0:0: CD-ROM PIONEER DVD-ROM DVD-116 1.21 PQ: 0 ANSI: 5
[ 4.067167] sr0: scsi3-mmc drive: 40x/40x cd/rw xa/form2 cdda tray
[ 4.067177] Uniform CD-ROM driver Revision: 3.20
[ 4.067454] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 4.067579] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 4.072187] scsi 1:0:1:0: CD-ROM HP CD-Writer cd16f 1.1D PQ: 0 ANSI: 5
[ 4.079184] sr1: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
[ 4.079397] sr 1:0:1:0: Attached scsi CD-ROM sr1
[ 4.079511] sr 1:0:1:0: Attached scsi generic sg2 type 5
[ 4.080939] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.080985] ehci_hcd 0000:02:09.2: enabling device (0014 -> 0016)
[ 4.081002] ehci_hcd 0000:02:09.2: PCI INT C -> GSI 23 (level, low) -> IRQ 23
[ 4.081046] ehci_hcd 0000:02:09.2: EHCI Host Controller
[ 4.081203] ehci_hcd 0000:02:09.2: new USB bus registered, assigned bus number 1
[ 4.104088] ehci_hcd 0000:02:09.2: irq 23, io mem 0xec000000
[ 4.116017] ehci_hcd 0000:02:09.2: USB 2.0 started, EHCI 0.95
[ 4.116201] usb usb1: configuration #1 chosen from 1 choice
[ 4.116261] hub 1-0:1.0: USB hub found
[ 4.116287] hub 1-0:1.0: 5 ports detected
[ 4.116542] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.116601] ohci_hcd 0000:02:09.0: enabling device (0014 -> 0016)
[ 4.116616] ohci_hcd 0000:02:09.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 4.116657] ohci_hcd 0000:02:09.0: OHCI Host Controller
[ 4.116785] ohci_hcd 0000:02:09.0: new USB bus registered, assigned bus number 2
[ 4.116823] ohci_hcd 0000:02:09.0: irq 21, io mem 0xed000000
[ 4.678203] usb usb2: configuration #1 chosen from 1 choice
[ 4.678264] hub 2-0:1.0: USB hub found
[ 4.678290] hub 2-0:1.0: 3 ports detected
[ 4.678497] ohci_hcd 0000:02:09.1: enabling device (0014 -> 0016)
[ 4.678519] ohci_hcd 0000:02:09.1: PCI INT B -> GSI 22 (level, low) -> IRQ 22
[ 4.678556] ohci_hcd 0000:02:09.1: OHCI Host Controller
[ 4.678675] ohci_hcd 0000:02:09.1: new USB bus registered, assigned bus number 3
[ 4.678723] ohci_hcd 0000:02:09.1: irq 22, io mem 0xec800000
[ 5.238174] usb usb3: configuration #1 chosen from 1 choice
[ 5.238243] hub 3-0:1.0: USB hub found
[ 5.238278] hub 3-0:1.0: 2 ports detected
[ 5.238507] uhci_hcd: USB Universal Host Controller Interface driver
[ 5.238646] uhci_hcd 0000:00:1f.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 5.238664] uhci_hcd 0000:00:1f.2: setting latency timer to 64
[ 5.238670] uhci_hcd 0000:00:1f.2: UHCI Host Controller
[ 5.238810] uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 4
[ 5.238866] uhci_hcd 0000:00:1f.2: irq 19, io base 0x0000b400
[ 5.239050] usb usb4: configuration #1 chosen from 1 choice
[ 5.239107] hub 4-0:1.0: USB hub found
[ 5.239129] hub 4-0:1.0: 2 ports detected
[ 5.239331] uhci_hcd 0000:00:1f.4: PCI INT C -> GSI 23 (level, low) -> IRQ 23
[ 5.239346] uhci_hcd 0000:00:1f.4: setting latency timer to 64
[ 5.239352] uhci_hcd 0000:00:1f.4: UHCI Host Controller
[ 5.239500] uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 5
[ 5.239561] uhci_hcd 0000:00:1f.4: irq 23, io base 0x0000b000
[ 5.239874] usb usb5: configuration #1 chosen from 1 choice
[ 5.239981] hub 5-0:1.0: USB hub found
[ 5.240090] hub 5-0:1.0: 2 ports detected
[ 5.240675] usbcore: registered new interface driver libusual
[ 5.240804] usbcore: registered new interface driver usbserial
[ 5.240830] USB Serial support registered for generic
[ 5.240864] usbcore: registered new interface driver usbserial_generic
[ 5.240870] usbserial: USB Serial Driver core
[ 5.240987] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 5.245385] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 5.245399] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 5.245699] mice: PS/2 mouse device common for all mice
[ 5.246116] rtc_cmos 00:05: RTC can wake from S4
[ 5.246280] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 5.246347] rtc0: alarms up to one month, 242 bytes nvram
[ 5.246691] device-mapper: uevent: version 1.0.3
[ 5.247241] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[ 5.247504] device-mapper: multipath: version 1.0.5 loaded
[ 5.247520] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 5.247961] EISA: Probing bus 0 at eisa.0
[ 5.248115] EISA: Detected 0 cards.
[ 5.248277] cpuidle: using governor ladder
[ 5.248288] cpuidle: using governor menu
[ 5.249871] TCP cubic registered
[ 5.250211] NET: Registered protocol family 10
[ 5.252078] lo: Disabled Privacy Extensions
[ 5.253343] NET: Registered protocol family 17
[ 5.253460] Bluetooth: L2CAP ver 2.11
[ 5.253468] Bluetooth: L2CAP socket layer initialized
[ 5.253479] Bluetooth: SCO (Voice Link) ver 0.6
[ 5.253487] Bluetooth: SCO socket layer initialized
[ 5.253725] Bluetooth: RFCOMM socket layer initialized
[ 5.253768] Bluetooth: RFCOMM TTY layer initialized
[ 5.253773] Bluetooth: RFCOMM ver 1.10
[ 5.253981] Using IPI No-Shortcut mode
[ 5.254213] registered taskstats version 1
[ 5.254637] Magic number: 9:919:423
[ 5.254912] rtc_cmos 00:05: setting system clock to 2009-05-08 09:26:49 UTC (1241774809)
[ 5.254924] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 5.254932] EDD information not available.
[ 5.256556] Freeing unused kernel memory: 532k freed
[ 5.256805] Write protecting the kernel text: 4128k
[ 5.256880] Write protecting the kernel read-only data: 1532k
[ 5.296875] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 5.552166] usb 5-1: new low speed USB device using uhci_hcd and address 2
[ 5.720964] usb 5-1: configuration #1 chosen from 1 choice
[ 6.432470] Floppy drive(s): fd0 is 1.44M
[ 6.453128] FDC 0 is a National Semiconductor PC87306
[ 6.661178] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k6-NAPI
[ 6.661193] e100: Copyright(c) 1999-2006 Intel Corporation
[ 6.661362] e100 0000:02:08.0: enabling device (0014 -> 0017)
[ 6.661418] e100 0000:02:08.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 6.690060] e100 0000:02:08.0: PME# disabled
[ 6.709987] e100: eth0: e100_probe: addr 0xed800000, irq 20, MAC addr 00:e0:18:44:47:43
[ 6.857303] ohci1394 0000:02:0a.0: enabling device (0014 -> 0016)
[ 6.857341] ohci1394 0000:02:0a.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 6.908672] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[22] MMIO=[eb800000-eb8007ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 7.198708] usbcore: registered new interface driver hiddev
[ 7.216278] input: USB Optical Mouse as /devices/pci0000:00/0000:00:1f.4/usb5/5-1/5-1:1.0/input/input4
[ 7.236669] generic-usb 0003:15CA:00C3.0001: input,hidraw0: USB HID v1.10 Mouse [USB Optical Mouse] on usb-0000:00:1f.4-1/input0
[ 7.236782] usbcore: registered new interface driver usbhid
[ 7.236798] usbhid: v2.6:USB HID core driver
[ 8.252634] ieee1394: Host added: ID:BUS[0-00:1023] GUID[003095268000686e]
[ 8.927226] PM: Starting manual resume from disk
[ 8.927249] PM: Resume from partition 8:7
[ 8.927259] PM: Checking hibernation image.
[ 8.927862] PM: Resume from disk failed.
[ 8.995400] kjournald starting. Commit interval 5 seconds
[ 8.995438] EXT3-fs: mounted filesystem with ordered data mode.
[ 16.978618] udev: starting version 141
[ 17.194952] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 17.245340] Linux agpgart interface v0.103
[ 17.270370] parport_pc 00:09: reported by Plug and Play ACPI
[ 17.270506] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[ 17.287795] agpgart-intel 0000:00:00.0: Intel 845G Chipset
[ 17.292486] agpgart-intel 0000:00:00.0: AGP aperture is 64M @ 0xf8000000
[ 17.518805] intel_rng: FWH not detected
[ 17.699971] iTCO_vendor_support: vendor-support=0
[ 17.725541] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
[ 17.725837] iTCO_wdt: failed to reset NO_REBOOT flag, reboot disabled by hardware
[ 17.725864] iTCO_wdt: No card detected
[ 18.065867] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 18.115732] synaptics was reset on resume, see synaptics_resume_reset if you have trouble on resume
[ 18.656249] psmouse serio1: ID: 10 00 64<6>ppdev: user-space parallel port driver
[ 19.337889] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input6
[ 19.433801] Intel ICH 0000:00:1f.5: enabling device (0004 -> 0005)
[ 19.433851] Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 19.433913] Intel ICH 0000:00:1f.5: setting latency timer to 64
[ 20.104026] intel8x0_measure_ac97_clock: measured 54711 usecs
[ 20.104033] intel8x0: clocking to 48000
[ 20.452531] lp0: using parport0 (interrupt-driven).
[ 20.852002] Adding 1871532k swap on /dev/sda5. Priority:-1 extents:1 across:1871532k
[ 20.861940] Adding 6281344k swap on /dev/sda7. Priority:-2 extents:1 across:6281344k
[ 20.977911] Adding 345356k swap on /dev/sda8. Priority:-3 extents:1 across:345356k
[ 21.619155] EXT3 FS on sda1, internal journal
[ 23.422279] type=1505 audit(1241774827.665:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=1963
[ 23.638131] type=1505 audit(1241774827.881:3): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=1967
[ 23.639002] type=1505 audit(1241774827.881:4): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=1967
[ 23.639417] type=1505 audit(1241774827.881:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=1967
[ 23.639726] type=1505 audit(1241774827.881:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=1967
[ 24.211341] type=1505 audit(1241774828.453:7): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=1972
[ 24.212586] type=1505 audit(1241774828.457:8): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=1972
[ 24.344778] type=1505 audit(1241774828.589:9): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=1976
[ 31.368306] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 31.368318] Bluetooth: BNEP filters: protocol multicast
[ 31.443122] Bridge firewalling registered
[ 37.773735] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 37.776233] e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
[ 37.792287] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 48.276025] eth0: no IPv6 routers present
[ 193.640056] usb 5-2: new full speed USB device using uhci_hcd and address 3
[ 193.784078] usb 5-2: not running at top speed; connect to a high speed hub
[ 193.873500] usb 5-2: configuration #1 chosen from 1 choice
[ 194.012165] Initializing USB Mass Storage driver...
[ 194.027085] scsi2 : SCSI emulation for USB Mass Storage devices
[ 194.046582] usbcore: registered new interface driver usb-storage
[ 194.046604] USB Mass Storage support registered.
[ 194.047072] usb-storage: device found at 3
[ 194.047080] usb-storage: waiting for device to settle before scanning
[ 199.054350] usb-storage: device scan complete
[ 199.070211] scsi 2:0:0:0: Direct-Access Maxtor Basics Portable 0122 PQ: 0 ANSI: 4
[ 199.084658] sd 2:0:0:0: [sdb] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
[ 199.087652] sd 2:0:0:0: [sdb] Write Protect is off
[ 199.087671] sd 2:0:0:0: [sdb] Mode Sense: 2d 08 00 00
[ 199.087682] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 199.148238] sd 2:0:0:0: [sdb] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
[ 199.151632] sd 2:0:0:0: [sdb] Write Protect is off
[ 199.151652] sd 2:0:0:0: [sdb] Mode Sense: 2d 08 00 00
[ 199.151663] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 199.151695] sdb: sdb1
[ 199.216921] sd 2:0:0:0: [sdb] Attached SCSI disk
[ 199.217251] sd 2:0:0:0: Attached scsi generic sg3 type 0
[ 555.192080] usb 5-2: USB disconnect, address 3
[ 2707.909027] ppdev0: registered pardevice
[ 2707.957072] ppdev0: unregistered pardevice
[ 2709.928620] ppdev0: registered pardevice
[ 2709.976926] ppdev0: unregistered pardevice
[ 2711.312452] ppdev0: registered pardevice
[ 2711.360125] ppdev0: unregistered pardevice
root@maxime-7d7a3085:/home/max# /mntsudo nautilus
bash: /mntsudo: Aucun fichier ou dossier de ce type
root@maxime-7d7a3085:/home/max# sudo nautilus

** (nautilus:6355): WARNING **: Unable to add monitor: Opération non prise en charge
Nautilus-Share-Message: Called "net usershare info" but it failed: « net usershare » a retourné l'erreur 255 : net usershare: cannot open usershare directory /var/lib/samba/usershares. Error Aucun fichier ou dossier de ce type
Please ask your system administrator to enable user sharing.
root@maxime-7d7a3085:/home/max# cfdisk -l
cfdisk: invalid option -- 'l'

Utilisation :
Afficher le numéro de version:
cfdisk -v
Afficher la table de partition:
cfdisk -P {r|s|t} [options] périphérique
Utilisation intéractive:
cfdisk [options] périphérique

Options:
-a: utiliser les touches fléchées au lieu de la surbrillance;
-z: débuter avec une table de partitions vierge, au lieu de la lire sur le disque;
-c C -h H -s S: écraser les paramètres connus du noyau: nombre de cylindres,
nombre de têtes et nombre de secteurs par piste.

Copyright © 1994-2002 Kevin E. Martin & aeb
root@maxime-7d7a3085:/home/max# cfdisk -p
cfdisk: invalid option -- 'p'

Utilisation :
Afficher le numéro de version:
cfdisk -v
Afficher la table de partition:
cfdisk -P {r|s|t} [options] périphérique
Utilisation intéractive:
cfdisk [options] périphérique

Options:
-a: utiliser les touches fléchées au lieu de la surbrillance;
-z: débuter avec une table de partitions vierge, au lieu de la lire sur le disque;
-c C -h H -s S: écraser les paramètres connus du noyau: nombre de cylindres,
nombre de têtes et nombre de secteurs par piste.

Copyright © 1994-2002 Kevin E. Martin & aeb
root@maxime-7d7a3085:/home/max# fdisk -l

Disque /dev/sda: 61.4 Go, 61475807232 octets
255 têtes, 63 secteurs/piste, 7474 cylindres
Unités = cylindres de 16065 * 512 = 8225280 octets
Identifiant de disque : 0x44a85606

Périphérique Amorce Début Fin Blocs Id Système
/dev/sda1 * 1 6372 51183058+ 83 Linux
/dev/sda2 6373 7474 8851815 5 Etendue
/dev/sda5 7242 7474 1871541 82 Linux swap / Solaris
/dev/sda6 7198 7241 353398+ 82 Linux swap / Solaris
/dev/sda7 6373 7154 6281352 82 Linux swap / Solaris
/dev/sda8 7155 7197 345366 82 Linux swap / Solaris

Les entrées de la table de partitions ne sont pas dans l'ordre du disque
root@maxime-7d7a3085:/home/max# fdisk -p
fdisk: invalid option -- 'p'

Utilisation : fdisk [-b TAILLE] [-u] DISQUE modifier la table de partitions
fdisk -l [-b TAILLE] [-u] DISQUE lister les tables de partitions

c'est juste une partie des commandes que j'ai effectue yen a eu une paire mais impossible de trouver mes fichiers qui etaient dans mon disque dur avant quand je demande l'acces au sda notamment il m'ecrit erreur fatale: partition logique erronee 6: chevauchement des partitions logique!!
bref c la grosse GALERE
donc d'apres vous est il possible que je retrouve mes fichiers et que je nettoie tout ca pour redemarrer comme avant avec xp! voilou
si ya qqn qui veut se pencher sur mon probleme et si ya une grosse bete en informatique qui peut me sauver ca serait super sympa
merci