[linux]driver HDD externe

Salut,

Quelle distribution ?
Que te renvoie la commande (en root) :

/sbin/fdisk -l

j'ai ubuntu, et voila le retour de commande

Disque /dev/sda: 160.0 Go, 160041885696 octets
255 heads, 63 sectors/track, 19457 cylinders
Units = cylindres of 16065 * 512 = 8225280 bytes
Disk identifier: 0x7e13b32a

Périphérique Amorce Début Fin Blocs Id Système
/dev/sda1 * 1 3647 29294496 83 Linux
/dev/sda2 3648 3896 2000092+ 82 Linux swap / Solaris
/dev/sda3 3897 19457 124993732+ 83 Linux

Disque /dev/sdb: 80.0 Go, 80026361856 octets
255 heads, 63 sectors/track, 9729 cylinders
Units = cylindres of 16065 * 512 = 8225280 bytes
Disk identifier: 0x8ee66999

Périphérique Amorce Début Fin Blocs Id Système
/dev/sdb1 1 9729 78148161 7 HPFS/NTFS

Merci pour ton aide

Ben apparemment il y a 2 disques de reconnus, un de 160 Go et un de 80 Go.
D'après la capacité, est-ce qu'un des deux pourrait s'apparenter à ton HD externe ?

Sinon, si le programme "hdparm" et les outils "smartmontools" sont installés que renvoient les commandes :

sudo hdparm -I /dev/sd*
sudo smartctl -i /dev/sd*

;-))

bonjour,
reconnu il y est mais il n'est certainement pas monte de plus il est en ntfs donc as tu installe ntfs-3g
as tu essaye sudo mount /dev/sdb1 /mnt/ddexterne pense a creer ddexterne
a+

Oui, le 160Go, c'est mon HDD principal, et celui de 80Go, c'est l'externe.

Voila le retour de commande de : hdparm -I /dev/sd*
Supported: 7 6 5 4
Likely used: 7
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 312581808
device size with M = 1024*1024: 152627 MBytes
device size with M = 1000*1000: 160041 MBytes (160 GB)
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, with device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Advanced power management level: unknown setting (0x0080)
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* NOP cmd
* DOWNLOAD_MICROCODE
* Advanced Power Management feature set
* SET_MAX security extension
Automatic Acoustic Management feature set
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
* General Purpose Logging feature set
* WRITE_{DMA|MULTIPLE}_FUA_EXT
* 64-bit World wide name
* IDLE_IMMEDIATE with UNLOAD
* Segmented DOWNLOAD_MICROCODE
* SATA-I signaling speed (1.5Gb/s)
* Native Command Queueing (NCQ)
* Host-initiated interface power management
* Phy event counters
DMA Setup Auto-Activate optimization
Device-initiated interface power management
* Software settings preservation
* SMART Command Transport (SCT) feature set
* SCT Long Sector Access (AC1)
* SCT LBA Segment Access (AC2)
* SCT Error Recovery Control (AC3)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
unknown 206[12]
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
not supported: enhanced erase
72min for SECURITY ERASE UNIT.
Checksum: correct

/dev/sda3:

ATA device, with non-removable media
Model Number: WDC WD1600BEVS-22RST0
Serial Number: WD-WXE507001160
Firmware Revision: 04.01G04
Standards:
Supported: 7 6 5 4
Likely used: 7
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 312581808
device size with M = 1024*1024: 152627 MBytes
device size with M = 1000*1000: 160041 MBytes (160 GB)
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, with device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Advanced power management level: unknown setting (0x0080)
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* NOP cmd
* DOWNLOAD_MICROCODE
* Advanced Power Management feature set
* SET_MAX security extension
Automatic Acoustic Management feature set
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
* General Purpose Logging feature set
* WRITE_{DMA|MULTIPLE}_FUA_EXT
* 64-bit World wide name
* IDLE_IMMEDIATE with UNLOAD
* Segmented DOWNLOAD_MICROCODE
* SATA-I signaling speed (1.5Gb/s)
* Native Command Queueing (NCQ)
* Host-initiated interface power management
* Phy event counters
DMA Setup Auto-Activate optimization
Device-initiated interface power management
* Software settings preservation
* SMART Command Transport (SCT) feature set
* SCT Long Sector Access (AC1)
* SCT LBA Segment Access (AC2)
* SCT Error Recovery Control (AC3)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
unknown 206[12]
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
not supported: enhanced erase
72min for SECURITY ERASE UNIT.
Checksum: correct

/dev/sdb:
HDIO_DRIVE_CMD(identify) failed: Invalid argument

/dev/sdb1:
HDIO_DRIVE_CMD(identify) failed: Invalid argument
root@math-laptop:/home/math# clear

root@math-laptop:/home/math# hdparm -I /dev/sd*

/dev/sda:

ATA device, with non-removable media
Model Number: WDC WD1600BEVS-22RST0
Serial Number: WD-WXE507001160
Firmware Revision: 04.01G04
Standards:
Supported: 7 6 5 4
Likely used: 7
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 312581808
device size with M = 1024*1024: 152627 MBytes
device size with M = 1000*1000: 160041 MBytes (160 GB)
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, with device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Advanced power management level: unknown setting (0x0080)
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* NOP cmd
* DOWNLOAD_MICROCODE
* Advanced Power Management feature set
* SET_MAX security extension
Automatic Acoustic Management feature set
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
* General Purpose Logging feature set
* WRITE_{DMA|MULTIPLE}_FUA_EXT
* 64-bit World wide name
* IDLE_IMMEDIATE with UNLOAD
* Segmented DOWNLOAD_MICROCODE
* SATA-I signaling speed (1.5Gb/s)
* Native Command Queueing (NCQ)
* Host-initiated interface power management
* Phy event counters
DMA Setup Auto-Activate optimization
Device-initiated interface power management
* Software settings preservation
* SMART Command Transport (SCT) feature set
* SCT Long Sector Access (AC1)
* SCT LBA Segment Access (AC2)
* SCT Error Recovery Control (AC3)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
unknown 206[12]
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
not supported: enhanced erase
72min for SECURITY ERASE UNIT.
Checksum: correct

/dev/sda1:

ATA device, with non-removable media
Model Number: WDC WD1600BEVS-22RST0
Serial Number: WD-WXE507001160
Firmware Revision: 04.01G04
Standards:
Supported: 7 6 5 4
Likely used: 7
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 312581808
device size with M = 1024*1024: 152627 MBytes
device size with M = 1000*1000: 160041 MBytes (160 GB)
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, with device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Advanced power management level: unknown setting (0x0080)
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* NOP cmd
* DOWNLOAD_MICROCODE
* Advanced Power Management feature set
* SET_MAX security extension
Automatic Acoustic Management feature set
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
* General Purpose Logging feature set
* WRITE_{DMA|MULTIPLE}_FUA_EXT
* 64-bit World wide name
* IDLE_IMMEDIATE with UNLOAD
* Segmented DOWNLOAD_MICROCODE
* SATA-I signaling speed (1.5Gb/s)
* Native Command Queueing (NCQ)
* Host-initiated interface power management
* Phy event counters
DMA Setup Auto-Activate optimization
Device-initiated interface power management
* Software settings preservation
* SMART Command Transport (SCT) feature set
* SCT Long Sector Access (AC1)
* SCT LBA Segment Access (AC2)
* SCT Error Recovery Control (AC3)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
unknown 206[12]
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
not supported: enhanced erase
72min for SECURITY ERASE UNIT.
Checksum: correct

/dev/sda2:

ATA device, with non-removable media
Model Number: WDC WD1600BEVS-22RST0
Serial Number: WD-WXE507001160
Firmware Revision: 04.01G04
Standards:
Supported: 7 6 5 4
Likely used: 7
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 312581808
device size with M = 1024*1024: 152627 MBytes
device size with M = 1000*1000: 160041 MBytes (160 GB)
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, with device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Advanced power management level: unknown setting (0x0080)
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* NOP cmd
* DOWNLOAD_MICROCODE
* Advanced Power Management feature set
* SET_MAX security extension
Automatic Acoustic Management feature set
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
* General Purpose Logging feature set
* WRITE_{DMA|MULTIPLE}_FUA_EXT
* 64-bit World wide name
* IDLE_IMMEDIATE with UNLOAD
* Segmented DOWNLOAD_MICROCODE
* SATA-I signaling speed (1.5Gb/s)
* Native Command Queueing (NCQ)
* Host-initiated interface power management
* Phy event counters
DMA Setup Auto-Activate optimization
Device-initiated interface power management
* Software settings preservation
* SMART Command Transport (SCT) feature set
* SCT Long Sector Access (AC1)
* SCT LBA Segment Access (AC2)
* SCT Error Recovery Control (AC3)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
unknown 206[12]
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
not supported: enhanced erase
72min for SECURITY ERASE UNIT.
Checksum: correct

/dev/sda3:

ATA device, with non-removable media
Model Number: WDC WD1600BEVS-22RST0
Serial Number: WD-WXE507001160
Firmware Revision: 04.01G04
Standards:
Supported: 7 6 5 4
Likely used: 7
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 312581808
device size with M = 1024*1024: 152627 MBytes
device size with M = 1000*1000: 160041 MBytes (160 GB)
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, with device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Advanced power management level: unknown setting (0x0080)
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* NOP cmd
* DOWNLOAD_MICROCODE
* Advanced Power Management feature set
* SET_MAX security extension
Automatic Acoustic Management feature set
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
* General Purpose Logging feature set
* WRITE_{DMA|MULTIPLE}_FUA_EXT
* 64-bit World wide name
* IDLE_IMMEDIATE with UNLOAD
* Segmented DOWNLOAD_MICROCODE
* SATA-I signaling speed (1.5Gb/s)
* Native Command Queueing (NCQ)
* Host-initiated interface power management
* Phy event counters
DMA Setup Auto-Activate optimization
Device-initiated interface power management
* Software settings preservation
* SMART Command Transport (SCT) feature set
* SCT Long Sector Access (AC1)
* SCT LBA Segment Access (AC2)
* SCT Error Recovery Control (AC3)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
unknown 206[12]
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
not supported: enhanced erase
72min for SECURITY ERASE UNIT.
Checksum: correct

/dev/sdb:
HDIO_DRIVE_CMD(identify) failed: Invalid argument

/dev/sdb1:
HDIO_DRIVE_CMD(identify) failed: Invalid argument
root@math-laptop:/home/math# clear

root@math-laptop:/home/math# hdparm -I /dev/sd*

/dev/sda:

ATA device, with non-removable media
Model Number: WDC WD1600BEVS-22RST0
Serial Number: WD-WXE507001160
Firmware Revision: 04.01G04
Standards:
Supported: 7 6 5 4
Likely used: 7
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 312581808
device size with M = 1024*1024: 152627 MBytes
device size with M = 1000*1000: 160041 MBytes (160 GB)
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, with device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Advanced power management level: unknown setting (0x0080)
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* NOP cmd
* DOWNLOAD_MICROCODE
* Advanced Power Management feature set
* SET_MAX security extension
Automatic Acoustic Management feature set
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
* General Purpose Logging feature set
* WRITE_{DMA|MULTIPLE}_FUA_EXT
* 64-bit World wide name
* IDLE_IMMEDIATE with UNLOAD
* Segmented DOWNLOAD_MICROCODE
* SATA-I signaling speed (1.5Gb/s)
* Native Command Queueing (NCQ)
* Host-initiated interface power management
* Phy event counters
DMA Setup Auto-Activate optimization
Device-initiated interface power management
* Software settings preservation
* SMART Command Transport (SCT) feature set
* SCT Long Sector Access (AC1)
* SCT LBA Segment Access (AC2)
* SCT Error Recovery Control (AC3)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
unknown 206[12]
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
not supported: enhanced erase
72min for SECURITY ERASE UNIT.
Checksum: correct

/dev/sda1:

ATA device, with non-removable media
Model Number: WDC WD1600BEVS-22RST0
Serial Number: WD-WXE507001160
Firmware Revision: 04.01G04
Standards:
Supported: 7 6 5 4
Likely used: 7
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 312581808
device size with M = 1024*1024: 152627 MBytes
device size with M = 1000*1000: 160041 MBytes (160 GB)
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, with device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Advanced power management level: unknown setting (0x0080)
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* NOP cmd
* DOWNLOAD_MICROCODE
* Advanced Power Management feature set
* SET_MAX security extension
Automatic Acoustic Management feature set
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
* General Purpose Logging feature set
* WRITE_{DMA|MULTIPLE}_FUA_EXT
* 64-bit World wide name
* IDLE_IMMEDIATE with UNLOAD
* Segmented DOWNLOAD_MICROCODE
* SATA-I signaling speed (1.5Gb/s)
* Native Command Queueing (NCQ)
* Host-initiated interface power management
* Phy event counters
DMA Setup Auto-Activate optimization
Device-initiated interface power management
* Software settings preservation
* SMART Command Transport (SCT) feature set
* SCT Long Sector Access (AC1)
* SCT LBA Segment Access (AC2)
* SCT Error Recovery Control (AC3)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
unknown 206[12]
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
not supported: enhanced erase
72min for SECURITY ERASE UNIT.
Checksum: correct

/dev/sda2:

ATA device, with non-removable media
Model Number: WDC WD1600BEVS-22RST0
Serial Number: WD-WXE507001160
Firmware Revision: 04.01G04
Standards:
Supported: 7 6 5 4
Likely used: 7
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 312581808
device size with M = 1024*1024: 152627 MBytes
device size with M = 1000*1000: 160041 MBytes (160 GB)
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, with device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Advanced power management level: unknown setting (0x0080)
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* NOP cmd
* DOWNLOAD_MICROCODE
* Advanced Power Management feature set
* SET_MAX security extension
Automatic Acoustic Management feature set
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
* General Purpose Logging feature set
* WRITE_{DMA|MULTIPLE}_FUA_EXT
* 64-bit World wide name
* IDLE_IMMEDIATE with UNLOAD
* Segmented DOWNLOAD_MICROCODE
* SATA-I signaling speed (1.5Gb/s)
* Native Command Queueing (NCQ)
* Host-initiated interface power management
* Phy event counters
DMA Setup Auto-Activate optimization
Device-initiated interface power management
* Software settings preservation
* SMART Command Transport (SCT) feature set
* SCT Long Sector Access (AC1)
* SCT LBA Segment Access (AC2)
* SCT Error Recovery Control (AC3)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
unknown 206[12]
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
not supported: enhanced erase
72min for SECURITY ERASE UNIT.
Checksum: correct

/dev/sda3:

ATA device, with non-removable media
Model Number: WDC WD1600BEVS-22RST0
Serial Number: WD-WXE507001160
Firmware Revision: 04.01G04
Standards:
Supported: 7 6 5 4
Likely used: 7
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 312581808
device size with M = 1024*1024: 152627 MBytes
device size with M = 1000*1000: 160041 MBytes (160 GB)
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, with device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Advanced power management level: unknown setting (0x0080)
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* NOP cmd
* DOWNLOAD_MICROCODE
* Advanced Power Management feature set
* SET_MAX security extension
Automatic Acoustic Management feature set
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
* General Purpose Logging feature set
* WRITE_{DMA|MULTIPLE}_FUA_EXT
* 64-bit World wide name
* IDLE_IMMEDIATE with UNLOAD
* Segmented DOWNLOAD_MICROCODE
* SATA-I signaling speed (1.5Gb/s)
* Native Command Queueing (NCQ)
* Host-initiated interface power management
* Phy event counters
DMA Setup Auto-Activate optimization
Device-initiated interface power management
* Software settings preservation
* SMART Command Transport (SCT) feature set
* SCT Long Sector Access (AC1)
* SCT LBA Segment Access (AC2)
* SCT Error Recovery Control (AC3)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
unknown 206[12]
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
not supported: enhanced erase
72min for SECURITY ERASE UNIT.
Checksum: correct

/dev/sdb:
HDIO_DRIVE_CMD(identify) failed: Invalid argument

/dev/sdb1:
HDIO_DRIVE_CMD(identify) failed: Invalid argument

Et la seconde commande :
/home/math# smartctl -i /dev/sd*
Le programme 'smartctl' n'est pas installé actuellement. Vous pouvez l'installer en tapant :
apt-get install smartmontools
bash: smartctl : commande introuvable

Bon apparemment la commande "hdparm" ne veut pas des disques branchés en USB ;-((

Donc dans un 1er temps, réponds au message de jeanbi s'il te plaît, merci, après on avisera ;-))

Voila ce qu'a dit jeanbi :

sudo mount /dev/sdb1 /mnt/ddexterne
[sudo] password for math:
$LogFile indicates unclean shutdown (0, 0)
Failed to mount '/dev/sdb1': Opération non supportée
Mount is denied because NTFS is marked to be in use. Choose one action:

Choice 1: If you have Windows then disconnect the external devices by
clicking on the 'Safely Remove Hardware' icon in the Windows
taskbar then shutdown Windows cleanly.

Choice 2: If you don't have Windows then you can use the 'force' option for
your own responsibility. For example type on the command line:

mount -t ntfs-3g /dev/sdb1 /mnt/ddexterne -o force

Or add the option to the relevant row in the /etc/fstab file:

/dev/sdb1 /mnt/ddexterne ntfs-3g defaults,force 0 0

Salut,

Affiches le résultat des commandes suivantes :

cat /etc/fstab
mount
ls -l /{mnt,media}

;-))

cat /etc/fstab
# /etc/fstab: static file system information.
#
# <file system> <mount point> <type> <options> <dump> <pass>
proc /proc proc defaults 0 0
# /dev/sda1
UUID=171fc704-0f3a-4e54-9a27-834f2e9859fe / ext3 defaults,errors=remount-ro 0 1
# /dev/sda3
UUID=f9f9f283-d8b9-4806-8e68-9fed902f4ebb /home ext3 defaults 0 2
# /dev/sda2
UUID=cad3ddc8-f4b1-4bfa-aa39-74504725c97f none swap sw 0 0
/dev/hda /media/cdrom0 udf,iso9660 user,noauto,exec 0 0

/dev/sda1 on / type ext3 (rw,errors=remount-ro)
proc on /proc type proc (rw,noexec,nosuid,nodev)
/sys on /sys type sysfs (rw,noexec,nosuid,nodev)
varrun on /var/run type tmpfs (rw,noexec,nosuid,nodev,mode=0755)
varlock on /var/lock type tmpfs (rw,noexec,nosuid,nodev,mode=1777)
udev on /dev type tmpfs (rw,mode=0755)
devshm on /dev/shm type tmpfs (rw)
devpts on /dev/pts type devpts (rw,gid=5,mode=620)
lrm on /lib/modules/2.6.22-14-generic/volatile type tmpfs (rw)
/dev/sda3 on /home type ext3 (rw)
securityfs on /sys/kernel/security type securityfs (rw)
binfmt_misc on /proc/sys/fs/binfmt_misc type binfmt_misc (rw,noexec,nosuid,nodev)

ls -l /{mnt,media}
/media:
total 8
lrwxrwxrwx 1 root root 6 2007-10-19 20:29 cdrom -> cdrom0
drwxr-xr-x 2 root root 4096 2007-10-19 20:29 cdrom0
drwx------ 2 root root 4096 2007-11-15 20:17 MATH

/mnt:
total 0

Voila, merci pour votre aide!!

Bon, on va essayer de reprendre à zéro...
Ouvre un terminal et tape les commandes suivantes :

cd /media 
sudo mkdir externe
sudo mount -t ntfs /dev/sdb1 /media/externe
mount 

Avant cette commande, j'ai fait les commandes précédentes(je précise quand même ;-))

sudo mount -t ntfs /dev/sdb1 /media/externe
$LogFile indicates unclean shutdown (0, 0)
Failed to mount '/dev/sdb1': Opération non supportée
Mount is denied because NTFS is marked to be in use. Choose one action:

Choice 1: If you have Windows then disconnect the external devices by
clicking on the 'Safely Remove Hardware' icon in the Windows
taskbar then shutdown Windows cleanly.

Choice 2: If you don't have Windows then you can use the 'force' option for
your own responsibility. For example type on the command line:

mount -t ntfs-3g /dev/sdb1 /media/externe -o force

Or add the option to the relevant row in the /etc/fstab file:

/dev/sdb1 /media/externe ntfs-3g defaults,force 0 0

mount
/dev/sda1 on / type ext3 (rw,errors=remount-ro)
proc on /proc type proc (rw,noexec,nosuid,nodev)
/sys on /sys type sysfs (rw,noexec,nosuid,nodev)
varrun on /var/run type tmpfs (rw,noexec,nosuid,nodev,mode=0755)
varlock on /var/lock type tmpfs (rw,noexec,nosuid,nodev,mode=1777)
udev on /dev type tmpfs (rw,mode=0755)
devshm on /dev/shm type tmpfs (rw)
devpts on /dev/pts type devpts (rw,gid=5,mode=620)
lrm on /lib/modules/2.6.22-14-generic/volatile type tmpfs (rw)
/dev/sda3 on /home type ext3 (rw)
securityfs on /sys/kernel/security type securityfs (rw)
binfmt_misc on /proc/sys/fs/binfmt_misc type binfmt_misc (rw,noexec,nosuid,nodev)

Bon on va tenter autre chose...
Redémare sous Windows, éjecte ton disque externe proprement, coupe l'alim du disque externe, redémarre ton pingouin, allumes ton disque externe, et raffiche la commande mount et essaie de remonter ton disque ensuite...

Le petit problème, c'est que je n'ai que linux sur ce PC... Plus de windows...

Je fait comment????O_o

bonjour,
et ben tu coupes le dd externe tu eteindsle micro tu le rallume sans allumer le dd externe et lorsque tu es sous l'interface graphique tu mets le dd externe en route et tu nous dis ce qui se passe .
a+

J'ai redémarré, je l'ai brancher et il me marque comme quoi il n'a pas pu monter le disque dur de 80Go...

Voici me message exact :

IMPOSSIBLE DE MONTER LE VOLUME
Impossible de monter le volume "sauvegarde donnée 80Go".

Détails :
$LogFile indicates unclean shutdown (0, 0) Failed to mount '/dev/sdb1': Opération non supportée Mount is denied because NTFS is marked to be in use. Choose one action : Choice 1 : If you have windows then disconnect the external devices by clicking on the 'safely Remove Hardware' icon in the Windows taskbar then shutdown Windows cleanly.
Choice 2 : If you don't have windows then you can use the 'force' option for you own responsibility. For example type on the command line : mount -t ntfs-3g /dev/sdb1 /media/sauvegarde donnée 80Go -o force Or add the option to the relevant row in the /etc/fstab file : /dev/sdb1 /media/sauvegarde donnée 80Go ntfs-3g defaults,force 0 0

VALIDEZ.

Ensuite, j'ai retapé la commande mount :

/dev/sda1 on / type ext3 (rw,errors=remount-ro)
proc on /proc type proc (rw,noexec,nosuid,nodev)
/sys on /sys type sysfs (rw,noexec,nosuid,nodev)
varrun on /var/run type tmpfs (rw,noexec,nosuid,nodev,mode=0755)
varlock on /var/lock type tmpfs (rw,noexec,nosuid,nodev,mode=1777)
udev on /dev type tmpfs (rw,mode=0755)
devshm on /dev/shm type tmpfs (rw)
devpts on /dev/pts type devpts (rw,gid=5,mode=620)
lrm on /lib/modules/2.6.22-14-generic/volatile type tmpfs (rw)
/dev/sda3 on /home type ext3 (rw)
securityfs on /sys/kernel/security type securityfs (rw)
binfmt_misc on /proc/sys/fs/binfmt_misc type binfmt_misc (rw,noexec,nosuid,nodev)

bonjour,
pourtant la solution est ecrite non !!

Choice 2 : If you don't have windows then you can use the 'force' option for you own responsibility. For example type on the command line : mount -t ntfs-3g /dev/sdb1 /media/sauvegarde donnée 80Go -o force Or add the option to the relevant row in the /etc/fstab file : /dev/sdb1 /media/sauvegarde donnée 80Go ntfs-3g defaults,force 0 0 

traduction tapes dans une console
sudo mount -t ntfs-3g /dev/sdb1 /mnt/ddexterne -o force
bien sur il faut que le paquet ntfs-3g soit installe
ou carrement dans /etc/fstab
rajouter cette ligne
/dev/sdb1 /mnt/ddexterne ntfs-3g defaults,force 0 0
mais commence par la 1er solution.
a+

Bon apparemment ton disque a été mal déconnecté depuis un système Windows :-\
Deux possibilités :
- Soit le rebrancher sur un système Windows et le déconnecter proprement
- Soit utiliser l'option "-o force" pour le monter à tes risques et périls...

Et quels sont les risques d'utiliser la commande "force"??????????
Comme le HDD n'est pas a moi, je n'ose pas trop faire ;) peur de faire des conneries...

re,
s'il n'est pas à toi , tu le rends à son proprio pour qu'il le démonte correctement .
a+

C'est ce que j'ai fait, mais ça ne marche toujours pas...

On l'a branché sous un win' XP, on l'a débranché proprement, et on a essayé de le rebrancher sous Ubuntu, mais ca ne marche toujours pas...:s