URC22B Télécommande universelle
Solved
Daria
-
Sb -
Sb -
Hello, I have a Thomson TV and a URC22B remote control. The problem is that the manual is in English, so I don't know how to make it work. Could someone help me?
Thank you
Thank you
15 réponses
Universal Remotes
N.S.E. URC 22
Code Entry
1. Turn on the device you want to control.
2. Press and hold the SET button, then press the button for the type of device you want to control (TV1, TV2, VCR1, ... AUX) at the same time.
3. The LED will light up, release the buttons.
4. Enter the 3-digit code for the device.
5. If the entered device code is correct, the LED will turn off automatically. If the code is incorrect, the LED will blink twice and stay in Setup mode (on), go back to step 4 with another code and repeat until the LED turns off.
6. Check that the remote buttons work correctly on the device. If not, repeat steps 2 to 6 with another code.
____________________
Quick Search
1. Turn on the device you want to control. If it's a VCR, a tape must be inserted.
2. Press and hold the SET button, then press the button for the type of device you want to control (TV1, TV2, VCR1, ... AUX) at the same time.
3. The LED will light up, release the buttons.
4. Press the SET button again. The URC 22 will enter Quick Search mode, and the LED will stay on.
5. Point the URC 22 at the device and press the POWER button. For VCR/AUX, you can press either POWER or PLAY. Watch if the device responds (Turns off or Plays). If the device responds, move to step 6. Otherwise, repeat step 5.
6. Check that other buttons such as CH +/-, VOL +/- work correctly (i.e., the device is being controlled properly). If not, return to step 5.
7. Some devices are slow to respond to the POWER signal. You can press the SET button to go back. With each press of this button, you reverse the direction of the search: forward or backward.
8. To exit Search mode, press the button corresponding to the device, and the LED will turn off.
Note: In Search mode, in addition to the SET button (SET and POWER buttons for VCR/AUX), the functionality of other buttons can be tested, meaning they can be checked without exiting Search mode. The URC 22 will exit Search mode if no button is pressed for 30 seconds.
_____________
Auto Search
1. Turn on the device you want to control. If it's a VCR, a tape must be inserted.
2. Press and hold the SET button, then press the POWER button for more than 3 seconds, and the Auto Search will begin.
3. Press any button to finish.
No further explanations, particularly about the duration of the search which may likely take several tens of minutes.
N.S.E. URC 22
Code Entry
1. Turn on the device you want to control.
2. Press and hold the SET button, then press the button for the type of device you want to control (TV1, TV2, VCR1, ... AUX) at the same time.
3. The LED will light up, release the buttons.
4. Enter the 3-digit code for the device.
5. If the entered device code is correct, the LED will turn off automatically. If the code is incorrect, the LED will blink twice and stay in Setup mode (on), go back to step 4 with another code and repeat until the LED turns off.
6. Check that the remote buttons work correctly on the device. If not, repeat steps 2 to 6 with another code.
____________________
Quick Search
1. Turn on the device you want to control. If it's a VCR, a tape must be inserted.
2. Press and hold the SET button, then press the button for the type of device you want to control (TV1, TV2, VCR1, ... AUX) at the same time.
3. The LED will light up, release the buttons.
4. Press the SET button again. The URC 22 will enter Quick Search mode, and the LED will stay on.
5. Point the URC 22 at the device and press the POWER button. For VCR/AUX, you can press either POWER or PLAY. Watch if the device responds (Turns off or Plays). If the device responds, move to step 6. Otherwise, repeat step 5.
6. Check that other buttons such as CH +/-, VOL +/- work correctly (i.e., the device is being controlled properly). If not, return to step 5.
7. Some devices are slow to respond to the POWER signal. You can press the SET button to go back. With each press of this button, you reverse the direction of the search: forward or backward.
8. To exit Search mode, press the button corresponding to the device, and the LED will turn off.
Note: In Search mode, in addition to the SET button (SET and POWER buttons for VCR/AUX), the functionality of other buttons can be tested, meaning they can be checked without exiting Search mode. The URC 22 will exit Search mode if no button is pressed for 30 seconds.
_____________
Auto Search
1. Turn on the device you want to control. If it's a VCR, a tape must be inserted.
2. Press and hold the SET button, then press the POWER button for more than 3 seconds, and the Auto Search will begin.
3. Press any button to finish.
No further explanations, particularly about the duration of the search which may likely take several tens of minutes.
booba
Good evening, I have a problem; the compatible codes for my TV are only 4 digits. What should I do?
angel02700
Bonsoir, j'ai un problème avec cette télécommande. Tous les codes fournis ne fonctionnent pas sauf un, mais chaque fois que j'appuie sur une touche, c’est la chaîne 1 qui reste. Avec les autres codes, ça ne fonctionne pas. En fait, quelle que soit la touche de la télécommande, ça me met la chaîne 1.
ludwiga
Thank you very much!
Severine
Thank you very much for your help. The third solution was the right one for my Toshiba television.
Sb
Thank you very much for your help.
