View original (French)

Wiring for autocom

Solved
amine00 Posted messages 142 Status Member -  
 adil -
Hello,
is the telephone wiring to connect digital/analog terminals to a digital switch (LG Nortel Aria SOHO) required to be done on separate telephone cables end-to-end like for the computer network, or is it possible to use a single cable containing multiple pairs (up to 16) to carry voice to/from the stations?
Will there be interference issues?
Is it possible to use a cat5e cable to connect 4 stations to the switch?

Thank you for your answers...
Configuration: Linux Debian Mozilla 1.8.1.3

11 answers

  1. sassi
     
    Bonjour

    S.O.S je cherche comment programmer l'autocommutateur LG Nortel ARIA SOHO (manuel de programmation en français), par exemple programmer un identificateur d'un pays qui n'existe pas dans la table préconfigurée (France 33)...
    Merci.
    12
    1. YOUSSEF
       
      HELLO MARHABA
      0663072587
      0
  2. Toufou13190 Posted messages 11061 Registration date   Status Member Last intervention   813
     
    Hello,
    telephone multipair cables are protected against interference, we can power all sockets with the same cable by only connecting the pair dedicated to each socket. The only problem is the connection; at each socket you either cut the cable, which can generate noise when connecting the wires for the next socket, or you strip a section of cable and only cut the concerned pair, but with a high risk of error on the color pairs and injuries on the pairs that continue, making it almost impossible to determine later where the cable is damaged.
    The ideal is a semi-star network with multipairs running from the PABX to sub-distributors, then simple cable distributors to each socket or pair of sockets if two stations are on the same desk.
    Good wiring!
    Cheers
    2
  3. amine00 Posted messages 142 Status Member 33
     
    Sorry to bring up this very old post, but it’s to reply to myself and share my experience since then with the readers.

    The ideal is to use a network cable (cat5, which is still the most common) for each socket from end to end. The benefit is to have standardized sockets that can be used for both telephony and also for computing if a change is needed at some point.
    1
  4. redsam
     
    Hello*
    Can we configure the Aria Soho standard with the LPD 7208 or do we need to have the LPD 7224?
    Thank you.
    1
    1. YOUSSEF
       
      YOUSSEF
      0663072587
      the positions that have access or pabx
      admin pc or the LDP-7224 position
      0
  6. amine00 Posted messages 142 Status Member 33
     
    Hi,
    thank you for your response. I forgot to mention that for now there will only be 5 outlets (and a maximum of 8 later) spread over 3 to 4 rooms, so I think the semi-star topology is too much for my needs...
    however, I didn't understand your initial suggestion to cut the cable at each outlet... if I cut the cable and not just one pair, how will I run the other pairs to the other outlets?
    0
  7. amine00 Posted messages 142 Status Member 33
     
    If I have the option to run a cable with a single pair end-to-end for each socket, is it better?
    0
  8. Toufou13190 Posted messages 11061 Registration date   Status Member Last intervention   813
     
    Hi,
    actually the multi-pair cable can be stripped for 10 cm at each outlet and on all the pairs so that only the pair affected at the outlet is cut.
    But of course the simplest solution remains to run a cable for each outlet with at least 3 pairs to be able to switch pairs in case of a failure due to a break in the length of the wire.
    See you!
    0
  9. amine00 Posted messages 142 Status Member 33
     
    Okay, and thanks again for the information... so in summary, it's best to use a dedicated cable for each outlet.
    0
  10. Toufou13190 Posted messages 11061 Registration date   Status Member Last intervention   813
     
    It's mainly simpler to avoid getting the wrong extension number!
    See you!
    0
  11. hassankaka Posted messages 8 Status Member
     
    Hello:
    Yes, if possible, to run a multi-pair cable for all the stations. However, there is a difference between analog and digital stations, as the analog station only supports one pair and the digital station supports two pairs.
    0
  12. Tarik mab
     
    Hello to all LG-Ericsson Aria Soho telephone system

    Standard issue how to display incoming number from director's phone

    Help me please

    Thank you
    0
    1. YOUSSEF
       
      YOUSSEF
      0663072787


      TL1 = Line key 1





      PROGRAMMING CODE
      *From extension 100 dial:
      *Trans / PGM * #

      PAYMENT CODE (212)
      *Trans/Pgm 100 + TL 1 + 212 + Hold/Save
      Restart the BABX (Trans/Pgm 450 + TL 15 + Hold/Save)

      DISPLAYING THE ENTERED NUMBER
      *Trans/Pgm 147 + c 01 03 TL 1 + 1 + Hold/Save

      CALL RESTRICTION
      *INTERNATIONAL ACCESS: (00 / 06 / ........Free)
      * T/PGM 116: (100100) + L1 + 01 + L2 + 01 + Hold/Save
      *National access: (05/06)
      * T/PGM 116: (101101) + L1 + 02 + L2 + 02 + Hold/Save
      * T/PGM 224: L2 + 01 + 00 + hold + (+) volume + 179 + HOLD
      *URBAN ACCESS: example CASA (
      *T/PGM 116: (102102) + L1 + 03 + L2 + 03 + hold
      *T/PGM 224: L3 + 01 0522 + hold
      *INTERCOM + Abbreviated Access
      * T/PGM 116: (103103) + L1 + 07 + L2 + 07 + hold
      *Programming Abbreviated Number:
      Trans / Pgm Speed (2000-2499) +PHONE NO +Hold 2 times
      Usage: Speed 2000 / 558 2000

      GROUP / LINE ACCESS
      lPGM141 + 01 01 + L1 + 1 + Hold (GROUP 1)
      lPGM141 + 02 02 + L1 + 2 + Hold (GROUP 2)
      lPGM141 + 03 03 + L1 + 3 + Hold (GROUP 3)

      lPGM117 + 100 100 + L1(On) + hold (extension 100 access group 1)
      lPGM117 + 101 101 + L1(On) and L2(On) + hold (extension 101 access group 1 and 2)
      lPGM117 + 102 107 + L1(On) and L2(Off) + hold (extension 102 J 107 access group 1 and not access group 2)

      RINGING OF LINES
      *PGM 144 + (01 03) + L1 + 1 + 100 100 + 0 + HOLD

      INTERNAL CALL INTERCEPTION (**)
      PGM 104 + 1 + HOLD
      PGM + 107 + L2 + * * + HOLD
      PGM + 190 + 620 + L1 + 6 + HOLD + L3 + 100-107 Dial the first extension
      and the last extension + HOLD example 8 extensions

      CALL TRANSFER
      PGM 182 + L2 + 031 + L3 + 000 + HOLD

      EXTERNAL MUSIC (Radio.....)
      PGM 171: L1 + 2 + hold + L2 + 2 + hold
      PGM 142: 01 03 + TL 6 + 2 + hold
      Listen to external music:
      Trans/pgm 73 + 02 + hold
      Disable MOH:
      Trans/pgm 73 + 00 + hold
      Listen to internal music:
      Trans/pgm 73 + 01 + hold

      PAGING
      *PGM 111 + Extension number 2f + TL 8 + 1 + HOLD
      Launch the voice call: 549 + Voice call
      Response to paging: 544

      13- PAGING

      Paging allows announcing messages, searching for people in predefined zones

      · Pick up the handset
      · Dial the paging code
      · After the beep, launch your message, hang up

      TAXATION (Prints the calls)
      *PGM 174 L1 + L1 + 5 (9600) + Hold/save
      *PGM 177 L2 + 1 + HOLD and L3 + 0 + Hold/save
      PGM 142: L3 + 02 (12KHZ) + HOLD
      *SERIAL CABLE CONFIGURATION:
      *2..........2
      *3..........3
      *5..........5

      INTERNAL LCR (1= 101)
      MP + T/P 220: TL1 + dial 5 (M12) + H/S
      MP + T/P 221:
      dial 000 + TL1 + 1 + H/S + TL2 + 1 + H/S + TL3 + 00 00 00 + H/S
      dial 001 + TL1 + 1 + H/S + TL2 + 2 + H/S + TL3 + 01 01 01 + H/S
      dial 002 + TL1 + 1 + H/S + TL2 + 3 + H/S + TL3 + 02 02 02 + H/S
      MP + T/P 222:
      dial 00 + TL1 + 101 + H/S + TL5 + DELETE + H/S
      dial 01 + TL1 + 102 + H/S + TL5 + DELETE + H/S
      dial 02 + TL1 + 103 + H/S + TL5 + DELETE + H/S

      AUTOMATIC ROUTING
      *PGM 220: L1 + 5 (M12) + Hold (Active LCR)
      *PGM 221: (LCR Table)
      dial 000 + L2 + 00 (area code) + HOLD + L3 + 00 00 00 + Hold
      dial 002 + L2 + 05 (area code) + HOLD + L3 + 00 00 00 + HOLD
      dial 003 + L2 + 0526 (area code) + HOLD + L3 + 01 01 01 + HOLD
      dial 004 + L2 + 0527 (area code) + HOLD + L3 + 01 01 01 + HOLD
      dial 005 + L2 + 0529 (area code) + HOLD + L3 + 01 01 01 + HOLD
      dial 006 + L2 + 0540 (area code) + HOLD + L3 + 01 01 01 + HOLD
      dial 001 + L2 + 06 (area code) + HOLD + L3 + 01 01 01 + HOLD
      Fix codes 00 and GSM codes 01
      *PGM 222:
      dial 00 + TL 5 + 1 + HOLD
      dial 01 + TL 5 + 2 + HOLD


      PROGRAMMING TIME AND DATE
      *PGM 178: L1 + HH MM + Hold + L2 + MM/DD/YY + Hold
      Change the time and date format:
      *PGM 169: L1 dial (1: 12H / 0:24) + HOLD

      PROGRAMMING OF KEYS
      *PGM 115: Extension number 2 times + 1 + key + Code:
      *01 + hold (clears the key)
      *02 + LINE No. + HOLD (01-12)
      *03 + GROUP No. (group programming of lines 1-8)
      *04 LOOP replaces all lines for call forwarding
      *05 + EXTENSION No. (station programming)
      EXPL.: Programming the keys of LDP-7724 extension
      *PGM 115: 101 101 + 1 + key1 + 0201(line 1) + H/S + TL2 + 0202(line 2) + H/S + 05101 + H/S (extension 101)
      or: Trans/Pgm + TL1-24 + Extension No + H/S


      FAX RECOGNITION
      *PGM 112: 107 107 + L11 + 1 + HOLD
      *PGM 161: L17 + line number + [HOLD/SAVE]

      DIALING PLAN
      PGM 104:
      1 (3 digits)
      6 (2 digits)

      NAME PROGRAMMING
      *PGM 164: TL 1 + Dial 100 + HOLD
      *PGM + 072 + 100 + Name + HOLD
      SEE TABLE




















      MOUCHARDE
      *PGM 113: 101 101 + TL4 + 1 (on) + hold
      *PGM 161: TL5 + 0 + hold + TL6 + 1 + hold
      *Moucharde programming:
      *PGM + key + T/P + 86 + hold
      *Mute programming:
      *PGM + key + T/P + 95 + Hold

      DSS 48 KEYS
      PGM 110: 101 101 + TL1 + 02 + TL2 + extension 100 + Hold

      HEADSET
      *PGM 111: Extension No + 2 + TL10 + hold + TL 11 + 1 + hold

      DISA
      PGM 140 - Line number 2 times + TL2 + TL1 DISA type + TL1 + 1 + hold

      PASSWORD
      PGM 162: 4 Digit code + HOLD

      EXTERNAL CONTROL CONTACT
      *PGM 168: TL1 + 1 + extension + hold
      *PGM 168: TL1 + 3 + hold

      MODEM
      *PGM 168: TL1 + extension + hold
      *PGM 168: TL2 + LINE No + hold

      CHANGE OF ANALOGUE POST TYPE P/T
      *PGM 110: Extension No 2 times TL1 + 07 (DTMF) / 08 (PULS) + hold

      DEVICE CAN RECEIVE A SIGNAL IN INTERCOM
      *PGM 111: Extension No 2 times TL6 + 1 + hold

      AUTOMATIC HOLD MUSIC/RING
      *PGM 112: Extension No 2 times TL2 + 1 + hold

      LINE ACCESS WITH CODE
      *PGM 141: Line number 2 times TL9 + 1 + hold
      NB: Need to program lock code: T/P 21 + 5 Digit Code + HOLD
      NB: From analogue extension: 9/8801 + code +# + PHONE No
      NB: From digital extension: TL + Code + HOLD + PHONE No

      LINE ACCESS FROM ALL EXTENSIONS

      NB: From digital extension: T/P 23 + CODE + TL + PHONE No
      NB: From analogue extension: 563 + CODE + FLASH + 9 + PHONE No

      INITIALIZATION
      Reset: PGM 450 TL14 + HOLD
      Restore the system: PGM 450 TL15 + HOLD


      HOTLINE / DIRECT ACCESS
      *PGM 122: Extension number 2 times +(1-4) + hold
      *1: Line key/ 2: Line / 3: Line group / 4: Extension

      HOLD MUSIC/RING
      *PGM 160: Extension number 2 times +(0: music / 1 : ring) + hold

      Preset Call Forward
      To make Preset Call Forward to STA (A)è(B)è(C)è(D)è(E)
      lPreset Call Forward: PGM 121
      l Preset Call Forward Timer: PGM 181-BTN12

















      Clear the lock code
      TRANS/PGM 105
      *Example: extension 102 the port is 002
      *Enter Port No (001-600): 003: 12345
      TRANS/PGM 227
      *Dial Port 002 +1=003
      *The lock code is 12345
      *To clear the code press Speed + Hold

      Executive & Secretary Transfer
      The executive station can be routed automatically to the associated secretary.
      lExecutive/Secretary Pair: PGM 229
      l CO Call To SEC: PGM 229-BTN2
      l Call EXEC If SEC DND: PGM 229-BTN3

      INTERNAL RESTRICTION:
      The extensions can call extension 100 and cannot call extensions 101 (CEO) except for extensions 102 130 140.
      0
    2. adil
       
      Pour transférer un appel à un autre poste, suivez ces étapes générales, bien que la procédure exacte puisse varier en fonction de votre système téléphonique : 1. **Répondez à l'appel.** 2. **Appuyez sur le bouton de transfert** (cela peut être marqué "Transferrer" ou avoir une icône spécifique). 3. **Composez le numéro du poste** sur lequel vous souhaitez transférer l'appel. 4. **Attendez que la personne réponde** (si vous souhaitez lui parler avant de transférer, sinon passez directement à l'étape suivante). 5. **Appuyez à nouveau sur le bouton de transfert** pour finaliser l'opération. Pour faire sonner deux postes en même temps, vous pouvez : 1. **Configurer un groupe d'appels** ou une sonnerie simultanée dans les paramètres de votre système téléphonique, si cela est disponible. 2. **Ajouter des numéros supplémentaires** à un appel en utilisant une fonction de conférence, si votre appareil le permet. Pour des instructions spécifiques, veuillez consulter le manuel de votre appareil ou le support technique de votre fournisseur de services.
      0