system error e000 canon ir 1600 Solved/Closed

Question

Good evening, I have a Canon IR 1600 copier that shows SYSTEM ERROR E000 after cleaning, I’m at my wit's end SOS, HELP.

Eureca · Accepted Answer

The E000 code relates to a problem with the fixing unit located on the left side of the copier. The major issue is that the unit is not powered so it cannot heat up, or that the heater for the fixing roller is out of service, or that the electrical part is out of service. Otherwise, if it’s just a bug, the error code needs to be cleared in service mode; in any case, the error code will need to be cleared ultimately.  Ciao see you later.

dododo · Answer

I have the same problem too.

ploqui · Answer

· Vérifiez que toutes les portes sont bien fermées, y compris la porte inférieure gauche. Accédez au mode service en appuyant sur * puis #. · Utilisez les touches gauche et droite et trouvez "imprimante". · Trouvez "réinitialiser l'imprimante". · Confirmez oui pour "réinitialiser l'imprimante". · Éteignez et rallumez après 5 secondes.  Ça fonctionne pour moi.  Bonne chance.

prince matouzebi · Answer

Hello, hi, I have a problem with my ir 1600 machine because it shows me the code e001.

yaro · Answer

Hello, hi, my problem is my Canon IR 2000 photocopier which displays the code: system error E 000. Thank you for responding.

Oumby · Answer

Hello I have a Canon IR 1018 photocopier that, when I start copying after scanning, does not copy and shows me an error message E 808. Please let me know what I should do.

vigilatus · Answer

Hello, I'm stuck and I have a ton of work to do with my copier at the office. It's displaying the error message E019 and the red light is on. How can I resolve this issue?

gypsoul · Answer

I tried this trick from my friend Ploqui that worked for the system error E000; I recommend that our friends facing the same problem give it a try.  Thanks Mr or Mrs Ploqui (thank you very much for your help...)    Check all doors are fully shut including the lower left door. Go into service mode by pressing * then #. · Use left and right keys and find “printer”. · find “reset printer”. · Confirm yes to “reset printer” · switch OFF for 5 seconds and ON again  It works for me.  Good luck

CHERKI · Answer

Hello everyone, I have a problem with a Canon IR1605 photocopier. I think it's due to an electric shock because when I turn it on, it gives me a system error e000. Is there a solution for this malfunction? I thank in advance anyone who gives me a solution, thank you.

faell · Answer

Hello, I have a CANON iR1610 that had an E000 error. The repair technician came this morning, and it means that the fuser in the copier is dead (the fuser allows the ink to be fixed at high temperature). Basically, there's nothing to do except replace it... pass the message... good luck (and to your sheet protector too).

erreur systeme e000 canon ir 1530 · Answer

Hello, I have a problem with my photocopier machine IR 1530, it shows a system error E000.

chapy · Answer

Veuillez suivre les étapes suivantes pour résoudre l'erreur E007 sur votre imprimante IR 2016 :

Éteignez l'imprimante et débranchez-la de l'alimentation.
    Vérifiez si le panneau arrière de l'imprimante est bien fermé.
    Ouvrez le couvercle et vérifiez le niveau de toner. Remplacez la cartouche si nécessaire.
    Vérifiez les rouleaux d'alimentation pour tout objet obstruant.
    Rebranchez l'imprimante et rallumez-la.
    Si l'erreur persiste, réinitialisez l'imprimante en accédant au menu de maintenance.

Si le problème n'est toujours pas résolu, il est conseillé de contacter un service technique professionnel.

eddythedove · Answer

Please also send me the solutions for the error codes from e000 to e007. Thank you in advance Eddythedove

mjcanon · Answer

Hello, I have a problem with the digital copiers IR where I often encounter system error codes E 019.  I need your help.    Thank you very much.

syphax · Answer

sslt here are the solutions for error codes from e000 to e007 E000 The main thermistor reading does not reach 40°C 14 seconds after the repair heater continues (low-temperature repair error)E001 The main thermistor reading reaches 220°C or higher (high-temperature repair error)E002 A start-up fault is detected under any of the following conditions of the main thermistor (start-up detection fault): after exceeding 40°C, it fails to reach 60°C within 10 seconds. after exceeding 60°C, it fails to reach 80°C within 10 seconds. ... after exceeding 180°C, it fails to reach 195°C within 10 seconds. E003 After the end of the WAIT period, the main thermistor reading is 100°C or lower. In standby, the sub-thermistor reading is 50°C or lower. (low temperature error in fixing temperature control) E004 At the time of initialization, the ZEROXI* signal from the power supply is not detected. During temperature control, the ZEROXI* signal does not arrive for 3 seconds continuously. A short circuit is detected in the triac (ASIC; fixing temperature control drive circuit error). Possible cause: Fixing assembly is faulty. (The main thermistor has an open circuit. The sub-thermistor has an open circuit. The fixing heater has an open circuit. The power supply PCB is faulty. The DC controller PCB is faulty.) Note: If E000 through E004 is indicated, the RAM on the image processor will retain the error memory of the fixing assembly after the power switch has been turned off and then on. Execute the following in service mode, and turn off and then on the power switch to clear the memory: #7 PRINTER - #4 PRINTER RESET - YES=(*) E010 A specific revolution is not detected from the main motor rotation detection signal (MLOK*), causing the signal to go '1' (main motor fault) Possible cause: The main motor (M101) is faulty. The controller PCB is faulty. E100 When the scanner motor is started up, the BD input signal does not arrive within a specific period of time. When the scanner motor is started up, the motor rotation is too fast and fails to reach a specific revolution within 20 seconds at the time of deceleration. While the scanner motor is rotating at a specific speed, the BD input signal cycle is not within a specific range (±2%) for an equivalent of 10 mm (print distance). While the scanner motor is rotating at a specific speed, the BD input signal cycle is not as indicated (±2%). During the WMUPR period after the power switch has been turned on or the front cover/left cover has been opened/closed, the drum unit is absent. Possible cause: The wiring is faulty (short circuit, open circuit). The laser scanner unit is faulty. The DC controller PCB is faulty. The drum unit is not installed. E719 The communication between the card reader and the image processor PCB is disrupted. Possible cause: The wiring is faulty (short circuit, open circuit). The card reader is faulty. The image processor PCB is faulty. Note: If E719 is indicated, the fault in communication is retained by the RAM on the image processor even when the power switch has been turned off and then on; be sure to execute #12 CLEAR - CARD in service mode before making corrections. E805 After the heat discharge fan drive signal is generated, the fan lock detection signal does not arrive for a specific period of time. Possible cause: The fan wiring is faulty (short circuit, open circuit). The heat discharge fan (FM101) is faulty. The DC controller PCB is faulty. Finisher Error Codes E500 An error has occurred in the communication between the machine and the finisher twice continuously. Possible cause: The harness to the finisher is faulty (disconnected connector, open circuit). The finisher controller PCB or the DC controller PCB is faulty. E514 The stack delivery belt does not reach home position when the stack handling motor (M2) is driven for a specific time (CW; if the same condition occurs during stack delivery, a jam will be identified). Possible cause: The stack handling motor (M2) is faulty. The stack delivery home position sensor (S8) is faulty. The connector is disconnected or has an open circuit. The stack handling motor relay harness is faulty. The stack delivery belt is faulty. The finisher controller PCB is faulty. E530 The rear aligning plate does not reach home position when the rear alignment motor (M4) has been driven for a specific time. The rear aligning plate does not reach home position when the rear alignment motor (M4) has been driven for a specific time. Possible cause: The rear alignment motor (M4) is faulty. The rear aligning plate home position sensor (S7) is faulty. The sensor connector is disconnected or has an open circuit. The rear alignment motor relay harness is faulty. The rear aligning plate is subjected to an abnormal load. The finisher controller PCB is faulty. E531 The stapler does not leave the stapling home position sensor (S13) within 0.5 seconds after the stapler motor (M6) is rotated CW. The stapler does not return to the home position sensor (S13) within 0.5 seconds after the stapler motor (M6) is driven CW and, in addition, it does not return to the sensor within 0.5 seconds after the motor is driven CCW thereafter. Possible cause: The stapler motor (M6) is faulty. The stapler home position sensor (SW1) is faulty. The stapler harness is faulty. The finisher controller PCB is faulty. E537 The front aligning plate does not reach home position when the front aligning motor (M3) is driven for a specific time. The front aligning plate does not leave home position when the front alignment motor (M3) is driven for a specific time. Possible cause: The front alignment motor (M3) is faulty. The front aligning plate home position sensor (S6) is faulty. The sensor connector is disconnected or has an open circuit. The front alignment motor relay harness is faulty. The front aligning plate is subjected to an abnormal load. The finisher controller PCB is faulty. E551 The delivery fan rotation signal (FNALCOK) does not arrive within 1 second when the heat discharge fan drive signal (FANON) is sent. Possible cause: The heat discharge fan (FM1) is faulty. The heat discharge fan relay harness is faulty. The heat discharge fan is subjected to an abnormal load. The finisher controller PCB is faulty. E577 The return roller does not reach home position when the delivery motor (M1) is driven for a specific time. (If the same condition is detected while alignment takes place in the direction of feed, a jam will be identified) Possible cause: The delivery motor (M1) on the finisher controller PCB is faulty. The return roller home position sensor (S3) is faulty. The connector is disconnected or has an open circuit. The delivery motor relay harness is faulty. The return roller is faulty. The finisher controller PCB is faulty. E580 The stack tray upper limit sensor (S1) goes ON while the stack tray up/down motor (M5) is in operation. The clock signal of the stack tray up/down clock sensor (S9) is not detected 15 times or more within 0.8 seconds while the stack tray up/down motor (M5) is in operation. It does not reach the stack tray paper height sensor (S10) 2 seconds after the stack tray up/down motor (M5) rotates for ascent. It does not leave the stack tray paper height sensor (S10) 2 seconds after the stack tray up/down motor (M5) starts to rotate for descent. Possible cause: The stack tray up/down motor (M5) is faulty. The stack tray paper height sensor (S10) is faulty. The sensor connector is disconnected or has an open circuit. The stack tray up/down clock sensor (SW9) is faulty. The sensor connector is disconnected or has an open circuit. The stack tray up/down motor is subjected to an abnormal load. The finisher controller PCB is faulty. E585 The stack retaining lever does not reach home position when the stack handling motor (M2) has been driven for a specific time (at the start of motor CCW rotation). (If the same condition is detected during stack delivery, a jam will be identified) Possible cause: The stack handling motor (M2) is faulty. The stack delivery lever home position sensor (S8) is faulty. The sensor connector is disconnected or has an open circuit. The stack handling motor relay harness is faulty. The stack retaining lever is faulty. The finisher controller PCB is faulty.   Canon iR2016 / iR2016J / iR2016i / iR2020 / iR2020i Error codes in the Fixing Unit E000 0000 Fixing temperature abnormal rise E001 0000 Fixing unit temperature rise detection (by main thermistor)  0001 Fixing unit temperature rise detection (by sub thermistor) E002 0000 Fixing unit temperature insufficient rise E003 0000 Low fixing temperature detection after standby (by main thermistor)  0001 Low fixing temperature detection after standby (by sub thermistor) E007 0000 Fixing film rotation error E010 0000 Main motor rotation error E019 0001 Waste toner full detection  0002 Waste toner full detection sensor failure E052 0000 Duplex unit connection error E100 0000 BD cycle out of range E197 0000 Erroneous communication with printer engine E500 0001 Finisher communication error E520 0000 Offset error E531 0000 Stapling error E540 0001 Paper surface not detected (standard tray)  0002 Not moved within the specified time (standard tray)  0003 Sensor not reached within 3 seconds (standard tray)  0005 Encoder clock failure (standard tray) E542 0001 Paper surface not detected (optional tray)  0002 Not moved within the specified time (optional tray)  0003 Sensor not reached within 3 seconds (optional tray)  0005 Encoder clock failure (optional tray) E575 0000 Stack delivery error E584 0000 Shutter failure E716 0000 Erroneous communication with optional cassette E719 0000 Erroneous communication with card reader (serial communication)  0002 Erroneous communication with coin vendor (serial communication) E733 0000 Erroneous communication between controller and printer E736 0000 CCU communication error E739 0000 Erroneous communication between controller and network board E744 0001 Language file/boot ROM/USB memory error  0002  0003  0004 E805 0000 Fan failure E808 0000 Fixing drive circuit failure

togacom · Answer

Good evening... I have this system error E100 after the cleaning... can someone help me...? Thank you

wahid · Answer

Hi, I hope to help you with your problem the error code system E000 is for cleaning, try cleaning the fan that is located behind the device, you can blow it with a compressor.

zeus2185 · Answer

Please also send me the solutions for the error codes from e000 to e003, thank you for sending them to me.

hopkins69 · Answer

Good evening my colleagues, I have read all the questions about your error E000 on the Canon IR 1600 copier and other series. Here is your error problem

- Oxidized or burnt heating element.
- Defective heating element (H1, H2 or H3).
- Blown fuse.
- Thermistor TH1 (bad contact or severed cable).
- Open thermal contact.
- Defective AC Power Board / SSR or Triac Q1.
- Defective control board.

And for other codes, here is the link to check: http://copieurs.free.fr/canon/codepancop.htm

For any other questions, I am at your disposal. hopkins69

hopkins16 · Answer

Good evening everyone, for the E000 code of the Canon IR 1600 here is the solution You simply need to clean your copier I am at your disposal, contact me on the forum, good luck.

mohaicha · Answer

Bonjour, j'ai un photocopieur Canon IR1605. Le problème, c'est que la copie n'est pas propre et même l'écriture du 1/3 de la première page se recopie sur les 2/3 de la deuxième page. Je veux le code SAV pour pouvoir accéder au contraste.

irelove · Answer

Hello my dear colleagues, Please kindly provide me with the list of error codes and possible solutions for Canon IR all series in French. Thank you, take care and see you soon.

omar · Answer

merci beaucoup Ploqui

Vérifiez que toutes les portes sont complètement fermées, y compris la porte inférieure gauche.
Entrez en mode service en appuyant sur * puis #.
· Utilisez les touches gauche et droite pour trouver « imprimante ».
· Trouvez « réinitialiser l'imprimante ».
· Confirmez oui pour « réinitialiser l'imprimante »
· Éteignez pendant 5 secondes, puis rallumez.

karlmweru2020 · Answer

Hi, for error code e000, you go to service mode and click on printer, and in printer, you do reset printer. And there you go, boom.

MAODESI · Answer

me too, the same problem, please help us anyway dear colleagues

karlmweru2020 · Answer

E000 means that your oven has a problem, but in most cases, this code appears after a sudden change in voltage. This means that in the case of a voltage issue, you go to service and click on printer and finally on reset. E007 is a problem related to the fixation. What other one do you need me to describe?

karlmweru2020 · Answer

E000 means that your oven has a problem, but in most cases, this code appears after a sudden voltage movement. This means that in the case of a voltage problem, you go to service mode and click on printer and finally on reset. E007 is a problem related to the fixing. What else do you need me to describe?

pathi · Answer

How can I decode my Canon IR1600 photocopier that displays system error E 000?

karlmweru2020 · Answer

Of course.

System error e000 canon ir 1600 - Page 2

Sharp xe-a217w - how to exit off mode?

Alcatel f685 trio black with answering machine

Texture issues in enshrouded

Old lullaby

Unable to connect to freebox os

Multiplex r4 ... "no signal" ???

Restoring a pc from bios?

Cd reading issues on ps3

Edit ad on leboncoin for free

Freebox wifi password