Tutorial for using vijeo designer
moun
-
R.bzh -
R.bzh -
Hello,
I am looking for someone who uses Vijeo Designer.
Or who can tell me where I can find a tutorial for using Vijeo Designer.
I have a XBT GK 5330 screen to program, but I am stuck on the event log :-(
Thank you very much for your help.
I am looking for someone who uses Vijeo Designer.
Or who can tell me where I can find a tutorial for using Vijeo Designer.
I have a XBT GK 5330 screen to program, but I am stuck on the event log :-(
Thank you very much for your help.
Configuration: Windows XP Internet Explorer 6.0
15 réponses
Hello, personally I am working on a piece processing project, but I have a problem. I created the installation diagram on Vijeo Designer but I can't automatically display it after the cycle start. As soon as I press the Cycle Start button, I want the system visualization screen to automatically switch to the Magelis screen. I have the same issue with alarms and safety measures. I can't find how to automatically display the alarm log after a system issue. I am currently in simulation mode.
Thank you for your understanding.
Best regards, Dj DooDoo
Thank you for your understanding.
Best regards, Dj DooDoo
For those looking for the Vijeo tutorial www.sitelec.org/themes/arenc/didacticiel_vijeo.pdf
http://lyc-augustin-thierry-blois.tice.ac-orleans-tours.fr/php5/bts_mai/doc/vijeo_designer_5.pdf
these 2 PDFs can help you.
http://lyc-augustin-thierry-blois.tice.ac-orleans-tours.fr/php5/bts_mai/doc/vijeo_designer_5.pdf
these 2 PDFs can help you.
Hello, having seen your tutorial, I would like to ask you a question regarding transferring a project to my XBT GT 5330.
It is actually a type program from the software and I can't transfer it to my graphical interface.
Thank you in advance.
It is actually a type program from the software and I can't transfer it to my graphical interface.
Thank you in advance.
Hello,
to transfer a vijeo project to an XBTGxxxx, there are two ways:
either the file system transfer to CF card
or the transfer via Ethernet. To do this, you need to go to "target properties" and declare the type of transfer you want to perform. If you choose Ethernet, you must specify the IP address of the XBTGxxxx terminal in the properties, then go to the machine to verify the address that has been assigned to it.
to transfer a vijeo project to an XBTGxxxx, there are two ways:
either the file system transfer to CF card
or the transfer via Ethernet. To do this, you need to go to "target properties" and declare the type of transfer you want to perform. If you choose Ethernet, you must specify the IP address of the XBTGxxxx terminal in the properties, then go to the machine to verify the address that has been assigned to it.
Hello everyone,
I've been using Vijeo Designer (V4.5) for 2 years for XBTGT6330 screens (touch screens) and developing all the applications for monitoring/reporting/alarm management/etc...
What information do you need?
I've been using Vijeo Designer (V4.5) for 2 years for XBTGT6330 screens (touch screens) and developing all the applications for monitoring/reporting/alarm management/etc...
What information do you need?
Hello Mimi
I'm new here.
I have a problem with my project, it's an XBT GK 5330, Vijeo Designer software, the Magelis is connected with my TSX 47 PLC via Unitelway.
During the testing of my project, there was a problem?
Everything I activate as an operation on the XBT I can no longer deactivate??? For example, transferring chocolate from conche 6 to tank 22 on
the PLC program which is done in PL7 3 has two variables, two words, one to activate and the other to deactivate, so I chose the option:
I took the dynamic keys R1 and R2 I chose general--> on press--> operation--> activate for R1 and deactivate for R2 of course with all that goes with the variable....
In fact, everything works except that when I want to deactivate or even for resetting the setpoint.
I noticed that in the PLC program, activate and deactivate are two different variables. So at the moment I activate my variable, it always stays at 1
because it is different from the deactivate variable.
Do momentary run and momentary stop help me in this case???
Otherwise, I am stuck
excerpt from the PLC program
Here is an example of how it is programmed in PL7 3 on the PLC for a start and stop command:
<START FILLED
!L74 if w13,0*(B175+B176+B177+B178)
THEN SET B179
<STOP
IF (W13,1 + NOT(B175+B176+B177+B178))*NOT W 13,0
THEN RESET B179
word 13,0 for my Magelis means start
word 13,1 for my Magelis means stop
the worst part is that I can't even know what B175 is because it is used in hundreds of equations like for example
B175 means: B170*I7,D*NOT B77*NOT B78---> B175 then I have to find for B170 and B170 and B78 etc......
I won't hide from you that B179 in this case is for activating and deactivating??? But why do I have two variables for my XBT?
Can you help me please?
I'm new here.
I have a problem with my project, it's an XBT GK 5330, Vijeo Designer software, the Magelis is connected with my TSX 47 PLC via Unitelway.
During the testing of my project, there was a problem?
Everything I activate as an operation on the XBT I can no longer deactivate??? For example, transferring chocolate from conche 6 to tank 22 on
the PLC program which is done in PL7 3 has two variables, two words, one to activate and the other to deactivate, so I chose the option:
I took the dynamic keys R1 and R2 I chose general--> on press--> operation--> activate for R1 and deactivate for R2 of course with all that goes with the variable....
In fact, everything works except that when I want to deactivate or even for resetting the setpoint.
I noticed that in the PLC program, activate and deactivate are two different variables. So at the moment I activate my variable, it always stays at 1
because it is different from the deactivate variable.
Do momentary run and momentary stop help me in this case???
Otherwise, I am stuck
excerpt from the PLC program
Here is an example of how it is programmed in PL7 3 on the PLC for a start and stop command:
<START FILLED
!L74 if w13,0*(B175+B176+B177+B178)
THEN SET B179
<STOP
IF (W13,1 + NOT(B175+B176+B177+B178))*NOT W 13,0
THEN RESET B179
word 13,0 for my Magelis means start
word 13,1 for my Magelis means stop
the worst part is that I can't even know what B175 is because it is used in hundreds of equations like for example
B175 means: B170*I7,D*NOT B77*NOT B78---> B175 then I have to find for B170 and B170 and B78 etc......
I won't hide from you that B179 in this case is for activating and deactivating??? But why do I have two variables for my XBT?
Can you help me please?
Hello, yes I have set the target for the operating terminal by entering the IP address and the subnet mask, but nothing works.
I created a very simple diagram and managed to transfer it to the graphical terminal but now it is impossible to import it to my computer.
However, if I take a program that has already been created by the software, it doesn't work either. I'll let you know tomorrow what error it shows me.
I really don't know what to do and moreover my teacher doesn't know how to handle this problem either.
I'm just looking but without answers.
Thanks again.
I created a very simple diagram and managed to transfer it to the graphical terminal but now it is impossible to import it to my computer.
However, if I take a program that has already been created by the software, it doesn't work either. I'll let you know tomorrow what error it shows me.
I really don't know what to do and moreover my teacher doesn't know how to handle this problem either.
I'm just looking but without answers.
Thanks again.
Yes thank you, I just managed to transfer a program.
I had to install some runtimes that I found in the start menu, and now it works.
Thanks again.
If I need help, I know who to ask.
I had to install some runtimes that I found in the start menu, and now it works.
Thanks again.
If I need help, I know who to ask.
Hello,
I would like to seek your help as I have a problem with my Magelis.
I have created my application using Vijeo Designer v4.5 and I want to transfer it to my Magelis XBTGT 6330.
I have installed Vijeo Run-Time without any problem via Ethernet. To do this, I configured the IP of my Magelis.
Once the installation was complete, I tried to transfer my application but I received a message saying: Transfer aborted due to a connection error. I then tried again using a USB cable and I got the same error.
I don't understand why I am getting this message because when I ping the Magelis to see if it is visible, it works fine. The version on the Magelis and the one of my application are identical. Additionally, once the Run-Time installation is complete, the Magelis stays on the Initial Boot Mode screen and tells me that to initialize the device, I need to download the Run-Time software, is this normal?
In short, I am not sure what to do. Thank you for your help.
I would like to seek your help as I have a problem with my Magelis.
I have created my application using Vijeo Designer v4.5 and I want to transfer it to my Magelis XBTGT 6330.
I have installed Vijeo Run-Time without any problem via Ethernet. To do this, I configured the IP of my Magelis.
Once the installation was complete, I tried to transfer my application but I received a message saying: Transfer aborted due to a connection error. I then tried again using a USB cable and I got the same error.
I don't understand why I am getting this message because when I ping the Magelis to see if it is visible, it works fine. The version on the Magelis and the one of my application are identical. Additionally, once the Run-Time installation is complete, the Magelis stays on the Initial Boot Mode screen and tells me that to initialize the device, I need to download the Run-Time software, is this normal?
In short, I am not sure what to do. Thank you for your help.
Hello, I'm new here.
So I have the same problem as "kevin--62220", which is as follows:
------------------------------ Transfer ------------------------------
---------------------- Checking connection ----------------------
Runtime Installer Error: [Target] [Xbt]. Target machine not found.
*** Transfer aborted due to a Runtime Installer error ***
I have a Magelis XBTGT1100 display, which only connects via a COM port.
Did you use a special cable to solve the runtime issue for transferring the program? I only have an RS232/RS485 cable to connect to my display.
I saw online that to connect, a XBTZG915 cable is needed.
So I wanted to know if a special cable is required, thank you for keeping me updated.
So I have the same problem as "kevin--62220", which is as follows:
------------------------------ Transfer ------------------------------
---------------------- Checking connection ----------------------
Runtime Installer Error: [Target] [Xbt]. Target machine not found.
*** Transfer aborted due to a Runtime Installer error ***
I have a Magelis XBTGT1100 display, which only connects via a COM port.
Did you use a special cable to solve the runtime issue for transferring the program? I only have an RS232/RS485 cable to connect to my display.
I saw online that to connect, a XBTZG915 cable is needed.
So I wanted to know if a special cable is required, thank you for keeping me updated.
Oh yes, I forgot to tell you that my screen is stuck on the diagram I created.
Is there a way to reset the XBT GT 5330?
Thank you.
Is there a way to reset the XBT GT 5330?
Thank you.
Hello.
So my problem is that I'm trying to communicate my XBT display with my PLC but it's not working :-(. I hope to find a solution here because you all seem to know your stuff.
My equipment: a TSX-Micro 3710 programmable PLC with PL7 PRO v4.5, a Magelis XBTGT1100 display programmable with Vijeo Designer v6.
I’m quite familiar with PL7 PRO: my program consists of a small system that picks up parts and performs a scan with a sensor, and once it finds an empty storage space, it inserts the part and returns to the origin. No problems there, it works under PL7 PRO.
I'm making a simple program where I just want to move an arm to get familiar with Vijeo Designer. This simple program is when I press a button on the display, the arm moves to the right.
I can create an interface in Vijeo Designer, but I'm having trouble with the dialog table; I must be using it incorrectly in the program. And since it's a digital display with buttons on the side (R1 to R6), I'm not sure if for the button to start the arm, I should press a side button (R1 to R6) or a touch button on the display.
And also if I really need what's in my dialog table: I made it for the actual program, it contains: 1 - Image of static function keys
2 - Image of system keys
3 - Image of numeric keys
6 - Number of the displayed page
16 - Number of the page to process
21 - Write permission for the table
Thank you for showing me how to program all of this in PL7 PRO and the variable assignment in Vijeo Designer.
If anyone can help me please, thank you and happy Halloween ^^
So my problem is that I'm trying to communicate my XBT display with my PLC but it's not working :-(. I hope to find a solution here because you all seem to know your stuff.
My equipment: a TSX-Micro 3710 programmable PLC with PL7 PRO v4.5, a Magelis XBTGT1100 display programmable with Vijeo Designer v6.
I’m quite familiar with PL7 PRO: my program consists of a small system that picks up parts and performs a scan with a sensor, and once it finds an empty storage space, it inserts the part and returns to the origin. No problems there, it works under PL7 PRO.
I'm making a simple program where I just want to move an arm to get familiar with Vijeo Designer. This simple program is when I press a button on the display, the arm moves to the right.
I can create an interface in Vijeo Designer, but I'm having trouble with the dialog table; I must be using it incorrectly in the program. And since it's a digital display with buttons on the side (R1 to R6), I'm not sure if for the button to start the arm, I should press a side button (R1 to R6) or a touch button on the display.
And also if I really need what's in my dialog table: I made it for the actual program, it contains: 1 - Image of static function keys
2 - Image of system keys
3 - Image of numeric keys
6 - Number of the displayed page
16 - Number of the page to process
21 - Write permission for the table
Thank you for showing me how to program all of this in PL7 PRO and the variable assignment in Vijeo Designer.
If anyone can help me please, thank you and happy Halloween ^^